How to Update Galaxy Fame S6810 with Android 4.1.2 XXAME2 Jelly Bean Official Firmware

Are You Looking For How to Update Galaxy Fame S6810 with Android 4.1.2 XXAME2 Jelly Bean Official Firmware

Samsung has released Android 4.1.2 Jelly Bean firmware update with base firmware XXAME2 on the Samsung Galaxy Fame with model number GT-S6810. The new official firmware is currently available in select Southeast Asia countries as an Over-The-Air (OTA) update as well as through Samsung KIES.

Firmware details
PDA: S6810XXAME2
CSC: S6810OLBAME1
MODEM: S6810DXAME1
Version: Android 4.1.2
Built date: May 31, 2013
Regions: Indonesia, Vietnam

Samsung Galaxy Fame S6810 users who missed the OTA update notification or unable to access the update over Samsung KIES, may follow our step-by-step guide to install the update manually.

Pre-requisites
1. Install USB Drivers for Samsung Galaxy Fame on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. Ensure the battery of the phone is charged more than 80 per cent.
5. The Android 4.1.2 XXAME2 Jelly Bean firmware is compatible only with Samsung Galaxy Fame S6810. Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy Fame by navigating to Settings >> About Phone.

File Required
1. Android 4.1.2 XXAME2 Jelly Bean Firmware for Samsung Galaxy Fame S6810
2. Odin 3.07

Steps to Update Galaxy Fame S6810 with Android 4.1.2 XXAME2 Jelly Bean Firmware
Step 1: Extract Firmware zip file that you downloaded already from above link using winrar/7zip/winzip or any other extracting tool, you will get a .tar.md5 file and some other files.
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Power off your phone. Wait 5-6 seconds for vibration to confirm complete switch off.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy Fame to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn blue with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.
Note: If the Added message does not appear, then try re-install USB drivers or changing the port on the computer.
Step 7: Choose the following files in Odin from extracted S6810XXAME2 firmware folder by using respective checkboxes:

• Select the PDA checkbox, and choose the file named .tar or .md5.
• Click the Phone checkbox, and choose the file with 'modem' in its name (ignore if there is no such file)
• Click the CSC checkbox, and select the file with 'csc' in its name (ignore if such file is missing)
• Choose the PIT checkbox, and choose the .pit file. Use only the file obtained during extracting in step 1 above, otherwise ignore it.

Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the START button to begin the installation process.
Step 10: Once the installation process is completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy Fame S6810 should be now updated with official Android 4.1.2 XXAME2 Jelly Bean. Head over to Settings >> About Phone to verify the software version running on the device.

Note: If Galaxy Fame S6810 stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up, Home and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.

Click here to know How to Root Galaxy Fame S6810 running on Android 4.1.2 Jelly Bean firmware.

Thanks for Read How to Update Galaxy Fame S6810 with Android 4.1.2 XXAME2 Jelly Bean Official Firmware Article

How to Unbrick Samsung Android Phones with One-Click UnBrick

Are You Looking For How to Unbrick Samsung Android Phones with One-Click UnBrick

Normally Samsung android phones are so secure to flash. But you are unlucky and got your phone bricked during flashing, rooting or upgrading.

Here is a good news for You – A developer come up with a software called One-Click UnBrick for Samsung android phones. This small utility uses Odin to repair our Samsung phones. Almost all Samsung phones with android éclair and above can be repair with this tool (few exceptions – it is working on some Android 1.5 too)


Requirements

• Install Samsung USB Driver for Mobile Phones  on the computer.
• Install Java Runtime Environment (JRE) on the computer.
• Download One-Click UnBrick tool.

Complete Step-By-Step Instructions:

1. Extract the "One-Click.jar" file using 7zip or any other extracting tool. Now you will get a "OneClick" folder.
2. Copy the "OneClick.jar" file and paste it into the "OneClick\heimdalloneclick\resources\HeimdallPackage" folder.
3. Right-click on the "oneclickloader.exe" file and choose "Run as Administrator".
4. Proceed with the installation of Heimdall.
5. After the installation is complete, you will see the the One-Click UnBrick interface.
6. Connect the phone to computer via USB and click on the "unsoft brick" button to recover your bricked Samsung android phone.

This method was originally posted via XDA-Developer original thread.

Thanks for Read How to Unbrick Samsung Android Phones with One-Click UnBrick Article

How to Root Galaxy Fame S6810 on Android 4.1.2 Jelly Bean Firmware

Are You Looking For How to Root Galaxy Fame S6810 on Android 4.1.2 Jelly Bean Firmware

Samsung has delivered its latest Android 4.1.2 Jelly Bean firmware update for the Galaxy Fame with model number GT-S6810 in several countries. The new official firmware is now available as an Over-The-Air (OTA) update as well as through Samsung KIES.

Samsung Galaxy Fame S6810 users who have already installed their devices with official Android 4.1.2 Jelly Bean firmware, may root their devices using the tutorial below.

This tutorial uses Motochopper file released by Recognized XDA-Developers, djrbliss. The Motochopper file allowing Galaxy Fame S6810 users to root their devices easily.

Disclaimer: Rooting voids the warranty of your device. We and the developer of this rooting procedures shall not be held responsible if any undesirable outcomes may happen to your device. use of this root guide is solely at your own risk!

Pre-requisites
1. Install USB Drivers for Samsung Galaxy Fame on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. Ensure the battery of the phone is charged more than 80 per cent.
5. The Root Package file works only on Samsung Galaxy Fame with model number GT-S6810. Applying these to any incorrect variant might brick the device. Verify the model number of the Galaxy Fame by navigating to Settings >> About Phone.

File Required
1. Root Package for Galaxy Fame S6810 (motochopper.zip)

Steps to Root Galaxy Fame S6810 Running on Android 4.1.2 Jelly Bean Firmware
Step 1: Extract the motochopper.zip file using winrar/7zip/winzip or any other extracting tool.
Step 2: Connect the phone to the computer using USB cable.
Step 3: If you are using Windows, navigate to the extracted directory and execute "run.bat". If you are using Linux or OS X, navigate to the extracted directory in a terminal and execute "./run.sh".
Step 4: Follow the on-screen instructions. Once the rooting procedure completes, the phone will boot into normal mode. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy Fame S6810 running on Android 4.1.2 Jelly Bean firmware is now rooted successfully. You can now install any app that requires root permission. Verify the root status of the device by downloading Root Checker app from Google Play Store.

Note: Tested working on Galaxy Fame S6810 with Android 4.1.2 XXAME2 Jelly Bean firmware, should work with other Jelly Bean firmware. Try it and let us know.

Thank's to all fellas at XDA who first tried out this rooting technique. This method was originally posted via XDA-Developers original thread.

Thanks for Read How to Root Galaxy Fame S6810 on Android 4.1.2 Jelly Bean Firmware Article

How to Root Galaxy Note 2 N7100 on Android 4.1.2 Jelly Bean Firmware

Are You Looking For How to Root Galaxy Note 2 N7100 on Android 4.1.2 Jelly Bean Firmware

Samsung Galaxy Note 2 N7100 users who have already installed their devices with Android 4.1.2 Jelly Bean, may root their devices using the tutorial below.

This tutorial uses CF-Auto-Root file released by recognised XDA Developers, Chainfire. The CF-Auto-Root file allowing Galaxy Note 2 users to root their devices easily without depending on the firmware. It completely supports Android 4.1.2 Jelly Bean and future firmware as well. Head over to the CF-Auto-Root main thread to learn more about the root method.

Note: Using this root increases your flash counter. The flash counter keeps track of how many custom firmwares you have flashed, as this voids warranty. Triangle Away can be used to reset the flash counter after installing CF-Auto-Root.

Disclaimer: Rooting voids the warranty of your device. We and the developer of this rooting procedures shall not be held responsible if any undesirable outcomes may happen to your device. use of this root guide is solely at your own risk!

Pre-requisites
1. Install USB Drivers for Samsung Galaxy Note 2 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy Note 2 should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 per cent.
6. The CF-Auto-Root file works only on Samsung Galaxy Note 2 N7100. Applying these to any incorrect variant might brick the device. Verify the model number of the Galaxy Note 2 by navigating to Settings >> About Phone.

File Required
1. CF-Auto-Root for Galaxy Note 2 N7100 (CF-Auto-Root-t03g-t03gxx-gtn7100.zip)
2. Odin 3.07

Steps to Root Galaxy Note 2 N7100 Running on Android 4.1.2 Jelly Bean Firmware
Step 1: Extract CF-Auto-Root and Odin 3.07 files using winrar/7zip/winzip or any other extracting tool.
Step 2: Switch off the Galaxy Note 2. Then boot the device into Download Mode by pressing and holding Volume Down, Home and Power buttons together until a construction Android robot icon with a warning triangle appears on screen. Now press the Volume Up button to enter Download Mode.
Step 3: Launch Odin on the computer as an Administrator.
Step 4: Connect the Galaxy Note 2 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn blue with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.
Note: If the Added message does not appear, then try re-install USB drivers or changing the port on the computer.
Step 5: In Odin, click the PDA button and select the CF-Auto-Root-t03g-t03gxx-gtn7100.tar.md5 file.
Step 6: Verify that Auto Reboot and F.Reset Time checkboxes are selected in Odin. Also, ensure the Re-Partition option is not selected.
Step 7: Double-check and click Start in Odin. The installation process will now begin.
Step 8: Once the installation process is completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy Note 2 N7100 running on Android 4.1.2 Jelly Bean firmware is now rooted successfully. You can now install any app that requires root permission. Verify the root status of the device by downloading Root Checker app from Google Play Store.

Thank's to all fellas at XDA who first tried out this rooting technique. This root method was originally posted via XDA-Developer original thread.

Thanks for Read How to Root Galaxy Note 2 N7100 on Android 4.1.2 Jelly Bean Firmware Article

How to Update Galaxy S4 I9500 with Android 4.2.2 XXUAMDE Jelly Bean Official Firmware

Are You Looking For How to Update Galaxy S4 I9500 with Android 4.2.2 XXUAMDE Jelly Bean Official Firmware

Samsung recently started rolling out its latest official firmware update for the Galaxy S4 with model number GT-I9500 in several countries. Most of these firmware updates come with security fixes and feature enhancements, while some offer bug-fixes and performance improvements over its previous iteration.

The Galaxy S4 I9500 users in Southeast Asia can now download and install the latest official Jelly Bean firmware, Android 4.2.2 XXUAMDE, through Samsung KIES as well as via Over-The-Air (OTA) update.

Firmware details
PDA: I9500XXUAMDE
CSC: I9500OLBAMDC
Version: Android 4.2.2
Built date: April, 2013
Regions: Indonesia, Malaysia, Philippines, Singapore, Vietnam, Thailand

The Galaxy S4 users who missed the OTA update notification and those who are residing outside the supported countries can manually download and install the same using our step-by-step guide given below.

Pre-requisites
1) Install USB Driver for Samsung Galaxy S4 on the computer.
2) Enable USB Debugging Mode.
3) Make a backup of all your important data before following the guide.
4) The Galaxy S4 should be factory unlocked and not locked to any particular carrier.
5) Ensure the battery of the phone is charged more than 80 per cent.
6) The Android 4.2.2 XXUAMDE Jelly Bean firmware is compatible only with Samsung Galaxy S4 I9500 and installing this on any incorrect variant will brick the device. Therefore, verify the model number of the Galaxy S4 by navigating to Settings >> About Phone.

Steps to install Android 4.2.2 XXUAMDE Jelly Bean on Samsung Galaxy S4 I9500
Step 1: Download Android 4.2.2 XXUAMDE Jelly Bean firmware for Samsung Galaxy S4 I9500 to the computer. Then extract the downloaded zip to get a file with .tar or .tar.md5 extension along with few other files
Step 2: Download Odin 3.07 which will help to install the Jelly Bean firmware
Step 3: Switch off the Galaxy S4. Then boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode
Step 4: Launch Odin on the computer
Step 5: Connect the Galaxy S4 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added. If Odin fails to detect the device then re-install USB driver.
Step 6: Select the files, which are extracted from the I9500XXUAMDE Jelly Bean folder, to install on the phone

• Click on PDA and select the file with .tar or .tar.md5 extension
• Click on Phone and select file with MODEM in its name
• Click on CSC and select file with CSC in its name
• Click on PIT and select the .pit file

Note: Ignore the steps b, c and d in case such files are not found.
Step 7: In Odin, verify the Auto Reboot and F. Reset Time checkboxes are selected. Also verify that the Re-Partition option is unchecked
Step 8: Double check everything and click the Start button in Odin to begin the firmware flashing. Upon the completion of the installation process, a message saying PASS will appear
Step 9: The phone will restart automatically. Once the home screen appears, safely unplug the USB cable from the phone to disconnect it from the computer

Samsung Galaxy S4 I9500 should be now updated with official Android 4.2.2 XXUAMDE Jelly Bean. Head over to Settings >> About Phone to verify the software version running on the device.

Click here to know How to Root Galaxy S4 I9500 running on Android 4.2.2 XXUAMDE Jelly Bean firmware.

Thanks for Read How to Update Galaxy S4 I9500 with Android 4.2.2 XXUAMDE Jelly Bean Official Firmware Article

How to Update Galaxy Note 2 N7100 with Android 4.1.2 XXDMG1 Jelly Bean Official Firmware

Are You Looking For How to Update Galaxy Note 2 N7100 with Android 4.1.2 XXDMG1 Jelly Bean Official Firmware

Samsung recently released a new software update with base firmware XXDMG1 for the owners of Samsung Galaxy Note 2 (GT-I9500) in India, Nepal, Sri Lanka, and Bangladesh. This firmware update is still based on Android 4.1.2 Jelly Bean.

Firmware details
PDA: N7100XXDMG1
CSC: N7100ODDDMG1
MODEM: N7100DDDMG1
Version: Android 4.1.2
Built date: Jul 1, 2013
Regions: India, Nepal, Sri Lanka, Bangladesh

The new official firmware is currently available as an Over-The-Air (OTA) update as well as through Samsung KIES. However, those who missed the OTA update notification or unable to access the update over Samsung KIES can download and install the same manually, using our step-by-step guide.

Pre-requisites
1. Install USB Drivers for Samsung Galaxy Note 2 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy Note 2 should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 per cent.
6. The Android 4.1.2 XXDMG1 Jelly Bean firmware is compatible only with Samsung Galaxy Note 2 N7100. Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy Note 2 by navigating to Settings >> About Phone.

File Required
1. Android 4.1.2 XXDMG1 Jelly Bean Firmware for Samsung Galaxy Note 2 N7100
2. Odin 3.07

Steps to Update Galaxy Note 2 N7100 with Android 4.1.2 XXDMG1 Jelly Bean Firmware
Step 1: Extract Firmware zip file that you downloaded already from above link using winrar/7zip/winzip or any other extracting tool, you will get a .tar.md5 file and some other files.
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Power off your phone. Wait 5-6 seconds for vibration to confirm complete switch off.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down, Home and Power buttons together until a construction Android robot icon with a warning triangle appears on screen. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy Note 2 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn blue with the COM port number. Additionally, the successful connected will be indicated by a message saying Added
Step 7: Choose the following files in Odin from extracted N7100XXDMG1 firmware folder by using respective checkboxes:

• Select the PDA checkbox, and choose the file named .tar or .md5.
• Click the Phone checkbox, and choose the file with 'modem' in its name (ignore if there is no such file)
• Click the CSC checkbox, and select the file with 'csc' in its name (ignore if such file is missing)
• Choose the PIT checkbox, and choose the .pit file. Use only the file obtained during extracting in step 1 above, otherwise ignore it.

Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the START button to begin the installation process.
Step 10: Once the installation process is completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy Note 2 N7100 should be now updated with official Android 4.1.2 XXDMG1 Jelly Bean firmware. Head over to Settings >> About Phone to verify the software version running on the device.

Note: If Galaxy Note 2 N7100 stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up, Home and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.

Click here to know How to Root Galaxy Note 2 N7100 running on Android 4.1.2 XXDMG1 Jelly Bean firmware.

Thanks for Read How to Update Galaxy Note 2 N7100 with Android 4.1.2 XXDMG1 Jelly Bean Official Firmware Article

How to Root Galaxy S4 I9500 on Android 4.2.2 XXUAMDE Jelly Bean Firmware

Are You Looking For How to Root Galaxy S4 I9500 on Android 4.2.2 XXUAMDE Jelly Bean Firmware

Samsung has started rolling out the Android 4.2.2 Jelly Bean update with base firmware XXUAMDE on the Exynos 5 octa-core variant of Samsung Galaxy S4 bearing model number GT-I9500. This official firmware is currently available for download through Samsung KIES as well as via Over-The-Air (OTA) update, for the Galaxy S4 users from Southeast Asia countries.

Samsung Galaxy S4 I9500 users who have already updated their devices with Android 4.2.2 XXUAMDE Jelly Bean, may root their devices using the tutorial below.

Disclaimer: Rooting voids the warranty of your device. We and the developer of this rooting procedures shall not be held responsible if any undesirable outcomes may happen to your device. use of this root guide is solely at your own risk!

Pre-requisites
1) Install USB Driver for Samsung Galaxy S4 on the computer.
2) Enable USB Debugging Mode on the phone.
3) Make a backup of all your important data before following the guide.
4) The Galaxy S4 I9500 should be factory unlocked and not locked to any particular carrier.
5) Ensure the battery of the phone is charged more than 80 per cent.
6) The stock recovery package works only on Samsung Galaxy S4 I9500 running on Android 4.2.2 XXUAMDE Jelly Bean. Applying these on any incorrect variant will brick the device. Verify the model number of the Galaxy S4 by selecting Settings >> About Phone.

Steps to root Galaxy S4 I9500 on Android 4.2.2 XXUAMDE Jelly Bean Firmware
Step 1: Download the SamsungI9500_cwm_Recovery_by cofface_0503.zip file for Samsung Galaxy S4 to the computer and extract using winrar/7zip/winzip or any other extracting tool.
[Note: The cofface_I9500_Recovery_en.zip file only works on old stock! We have replaced it with SamsungI9500_cwm_Recovery_by cofface_0503.zip file. This method was originally posted via XDA-Developer original thread.]
Step 2: Download Odin 3.07 and extract the zip file
Step 3: Switch off the Galaxy S4. Then boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode
Step 4: Launch Odin on the computer.
Step 5: Connect the Galaxy S4 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added. If Odin fails to detect the device then re-install USB driver.
Step 6: In Odin, click the PDA button and select the cofface_samsungI9500_recovery_en_0503.tar file
Step 7: Verify that Auto Reboot and F.Reset Time checkboxes are selected in Odin. DO NOT Tick "Re-partition" options.
Step 8: Finally hit the Start button in Odin to begin the flashing. The installation will take some time
Step 9: When the installation process is completed the phone will restart automatically. Once the home screen appears on the phone users may safely unplug the device from the computer
Step 10: Switch off the Galaxy S4. Then boot the phone into recovery mode by pressing and holding Volume Up, Home and Power buttons together and select ROOT YOUR PHONE.
Step 11: Once rooting process is completed, return to main recovery menu and select reboot system now to reboot phone.

Samsung Galaxy S4 I9500 running on official Android 4.2.2 XXUAMDE Jelly Bean is now rooted successfully.

[Note: If this method doesn't work try Adam Kernel (including AutoRoot with SuperSU v1.25) or Chainfire's CF-Auto-Root methods.]

Thank's to all fellas at XDA who first tried out this rooting technique. This root method was originally posted via XDA-Developers original thread.

Thanks for Read How to Root Galaxy S4 I9500 on Android 4.2.2 XXUAMDE Jelly Bean Firmware Article

How to Root Galaxy Note 2 N7100 on Android 4.1.2 XXDMG1 Jelly Bean Firmware

Are You Looking For How to Root Galaxy Note 2 N7100 on Android 4.1.2 XXDMG1 Jelly Bean Firmware

Samsung has released its latest Android 4.1.2 Jelly Bean update with firmware build number N7100XXDMG1 for the international version of Samsung Galaxy Note 2 bearing model number GT-N7100.

Samsung Galaxy Note 2 N7100 users who have already updated their devices with Android 4.1.2 XXDMG1 Jelly Bean, may root their devices using the tutorial below.

This tutorial uses CF-Auto-Root file released by recognised XDA Developers, Chainfire. The CF-Auto-Root file allowing Galaxy Note 2 users to root their devices easily without depending on the firmware. It completely supports Android 4.1.2 Jelly Bean and future firmware as well. Head over to the CF-Auto-Root main thread to learn more about the root method.

Note: Using this root increases your flash counter. The flash counter keeps track of how many custom firmwares you have flashed, as this voids warranty. Triangle Away can be used to reset the flash counter after installing CF-Auto-Root.

Disclaimer: Rooting voids the warranty of your device. We and the developer of this rooting procedures shall not be held responsible if any undesirable outcomes may happen to your device. use of this root guide is solely at your own risk!

Pre-requisites
1. Install USB Drivers for Samsung Galaxy Note 2 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy Note 2 should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 per cent.
6. The CF-Auto-Root file works only on Samsung Galaxy Note 2 N7100. Applying these to any incorrect variant might brick the device. Verify the model number of the Galaxy Note 2 by navigating to Settings >> About Phone.

File Required
1. CF-Auto-Root for Galaxy Note 2 N7100 (CF-Auto-Root-t03g-t03gxx-gtn7100.zip)
2. Odin 3.07

Steps to Root Galaxy Note 2 N7100 Running on Android 4.1.2 XXDMG1 Jelly Bean Firmware
Step 1: Extract CF-Auto-Root and Odin 3.07 files using winrar/7zip/winzip or any other extracting tool.
Step 2: Switch off the Galaxy Note 2. Then boot the device into Download Mode by pressing and holding Volume Down, Home and Power buttons together until a construction Android robot icon with a warning triangle appears on screen. Now press the Volume Up button to enter Download Mode.
Step 3: Launch Odin on the computer as an Administrator.
Step 4: Connect the Galaxy Note 2 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn blue with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.
Note: If the Added message does not appear, then try re-install USB drivers or changing the port on the computer.
Step 5: In Odin, click the PDA button and select the CF-Auto-Root-t03g-t03gxx-gtn7100.tar.md5 file.
Step 6: Verify that Auto Reboot and F.Reset Time checkboxes are selected in Odin. Also, ensure the Re-Partition option is not selected.
Step 7: Double-check and click Start in Odin. The installation process will now begin.
Step 8: Once the installation process is completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy Note 2 N7100 running on Android 4.1.2 XXDMG1 Jelly Bean firmware is now rooted successfully. You can now install any app that requires root permission. Verify the root status of the device by downloading Root Checker app from Google Play Store.

Thank's to all fellas at XDA who first tried out this rooting technique. This root method was originally posted via XDA-Developer original thread.

Click here to know How to Update Galaxy Note 2 N7100 with official Android 4.1.2 XXDMG1 Jelly Bean firmware.

Thanks for Read How to Root Galaxy Note 2 N7100 on Android 4.1.2 XXDMG1 Jelly Bean Firmware Article

How to Update Galaxy S4 I9505 with Android 4.2.2 XXUBMG5 Jelly Bean Official Firmware

Are You Looking For How to Update Galaxy S4 I9505 with Android 4.2.2 XXUBMG5 Jelly Bean Official Firmware

Another official firmware update with build number I9505XXUBMG5 has been rolled out on the LTE variant of Samsung Galaxy S4 (GT-I9505) with Snapdragon processors. This new software update is still based on Android 4.2.2 Jelly Bean version and now available in some Southeast Asian countries - Malaysia, Philippines, and Singapore.

Firmware details
PDA: I9505XXUBMG5
CSC: I9505OLBBMG1
MODEM: I9505DXUBMG5
Version: Android 4.2.2
Built date: Jul 05, 2013
Regions: Malaysia, Philippines, Singapore

The new official firmware is currently available as an Over-The-Air (OTA) update as well as through Samsung KIES. However, those who missed the OTA update notification or unable to access the update over Samsung KIES can download and install the same manually, using our step-by-step guide.

Pre-requisites
1. Install USB Drivers for Samsung Galaxy S4 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy S4 should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 per cent.
6. The Android 4.2.2 XXUBMG5 Jelly Bean firmware is compatible only with Samsung Galaxy S4 I9505. Applying these to any incorrect variant might brick the device. Verify the model number of the Galaxy S4 by navigating to Settings >> About Phone.

File Required
1. Android 4.2.2 XXUBMG5 Jelly Bean Firmware for Samsung Galaxy S4 I9505
2. Odin 3.07

Steps to Update Galaxy S4 I9505 with Android 4.2.2 XXUBMG5 Jelly Bean Firmware
Step 1: Extract Firmware zip file that you downloaded already from above link using winrar/7zip/winzip or any other extracting tool, you will get a .tar.md5 file and some other files.
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Power off your phone. Wait 5-6 seconds for vibration to confirm complete switch off.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down, Home and Power buttons together until a construction Android robot icon with a warning triangle appears on screen. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy S4 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn blue with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.
Note: If the Added message does not appear, then try re-install USB drivers or changing the port on the computer.
Step 7: Choose the following files in Odin from extracted I9505XXUBMG5 firmware folder by using respective checkboxes:

• Select the PDA checkbox, and choose the file named .tar or .md5.
• Click the Phone checkbox, and choose the file with 'modem' in its name (ignore if there is no such file)
• Click the CSC checkbox, and select the file with 'csc' in its name (ignore if such file is missing)
• Choose the PIT checkbox, and choose the .pit file. Use only the file obtained during extracting in step 1 above, otherwise ignore it.

Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the START button to begin the installation process.
Step 10: Once the installation process is completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy S4 I9505 should be now updated with official Android 4.2.2 XXUBMG5 Jelly Bean. Head over to Settings >> About Phone to verify the software version running on the device.

Note: If Galaxy S4 I9505 stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up, Home and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.

Click here to know How to Root Galaxy S4 I9505 running on Android 4.2.2 XXUBMG5 Jelly Bean firmware.

Thanks for Read How to Update Galaxy S4 I9505 with Android 4.2.2 XXUBMG5 Jelly Bean Official Firmware Article

How to Unroot Galaxy S4 I9500 on Android 4.2.2 XXUAMDE Jelly Bean Firmware

Are You Looking For How to Unroot Galaxy S4 I9500 on Android 4.2.2 XXUAMDE Jelly Bean Firmware

Samsung Galaxy S4 I9500 users can now unroot their device to recover the phone's warranty by using this guide. In order to regain the device hardware warranty, users must install Triangle Away app to reset flash counter to zero and then follow the steps in this guide to unroot the device successfully.

Pre-requisites
1. Install USB Driver for Samsung Galaxy S4 on the computer.
2. Enable USB Debugging Mode.
3. Make a backup of all your important data before following the guide.
4. The Galaxy S4 should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 per cent.
6. The Android 4.2.2 XXUAMDE Jelly Bean firmware is compatible only with Samsung Galaxy S4 I9500 and installing this on any incorrect variant will brick the device. Therefore, verify the model number of the Galaxy S4 by navigating to Settings>> About Phone.

File Required
1. Android 4.2.2 I9500XXUAMDE Jelly Bean Firmware
2. Odin 3.07

Steps to Unroot Galaxy S4 I9500 on Android 4.2.2 XXUAMDE Jelly Bean Firmware
Step 1: Extract Firmware zip file that you downloaded already from above link, you will get a .tar.md5 file and some other files.  
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.  
Step 3: Power off your phone. Wait 5-6 seconds for vibration to confirm complete switch off. 
Step 4: Boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy S4 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added. If Odin fails to detect the device then re-install USB driver.
Step 7: Choose the following files in Odin from extracted I9500XXUAMDE firmware folder by using respective checkboxes:

• Select the PDA checkbox, and choose the file named .tar or .md5.
• Click the Phone checkbox, and choose the file with 'modem' in its name (ignore if there is no such file)
• Click the CSC checkbox, and select the file with 'csc' in its name (ignore if such file is missing)
• Choose the PIT checkbox, and choose the .pit file. Use only the file obtained during extracting in step 1 above, otherwise ignore it.

Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the START button to begin the flashing process.
Step 10: Once flashing completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy S4 I9500 running on official Android 4.2.2 XXUAMDE Jelly Bean is now Unrooted successfully. However, to get back warranty you should first use triangle away to set flash counter to zero and then follow the above steps.

Thanks for Read How to Unroot Galaxy S4 I9500 on Android 4.2.2 XXUAMDE Jelly Bean Firmware Article

How to Update Galaxy Note 2 N7100 with Android 4.1.2 XXDMD2 Jelly Bean Official Firmware

Are You Looking For How to Update Galaxy Note 2 N7100 with Android 4.1.2 XXDMD2 Jelly Bean Official Firmware

Samsung has started rolling out the Android 4.1.2 Jelly Bean update with base firmware XXDMD2 for the Galaxy Note 2 GT-N7100. This official update is currently available for download via Over-The-Air (OTA) update as well as through Samsung KIES, for the Galaxy Note 2 users from Southeast Asia countries.

Firmware details
PDA: N7100XXDMD2
CSC: N7100OLBDMD2
Version: Android 4.1.2
Built date: April, 2013
Regions: Indonesia, Malaysia, Philippines, Singapore, Vietnam, Thailand

The Galaxy Note 2 users who fail to upgrade their devices with Android 4.1.2 Jelly Bean using official method for being region specific, may follow our step-by-step guide to install the update manually.

Pre-requisites
1. Install USB Driver for Samsung Galaxy Note on the computer.
2. Enable USB Debugging Mode.
3. Make a backup of all your important data before following the guide.
4. The Galaxy Note 2 should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 per cent.
6. The Android 4.1.2 XXDMD2 Jelly Bean firmware is compatible only with Samsung Galaxy Note 2 N7100 and installing this on any incorrect variant will brick the device. Therefore, verify the model number of the Galaxy Note 2 by navigating to Settings>> About Phone.

File Required
1. Android 4.1.2 XXDMD2 Jelly Bean Firmware
2. Odin 3.07

Steps to Update Galaxy Note 2 N7100 with Android 4.1.2 XXDMD2 Jelly Bean Firmware
Step 1: Extract Firmware zip file that you downloaded already from above link, you will get a .tar.md5 file and some other files.
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Power off your phone. Wait 5-6 seconds for vibration to confirm complete switch off.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy Note 2 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added. If Odin fails to detect the device then re-install USB driver.
Step 7: Choose the following files in Odin from extracted N7100XXDMD2 firmware folder by using respective checkboxes:

• Select the PDA checkbox, and choose the file named .tar or .md5.
• Click the Phone checkbox, and choose the file with 'modem' in its name (ignore if there is no such file)
• Click the CSC checkbox, and select the file with 'csc' in its name (ignore if such file is missing)
• Choose the PIT checkbox, and choose the .pit file. Use only the file obtained during extracting in step 1 above, otherwise ignore it.

Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the START button to begin the flashing process.
Step 10: Once flashing completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy Note 2 N7100 should be now updated with official Android 4.1.2 XXDMD2 Jelly Bean. Head over to Settings>> About Phone to verify the software version running on the device.

Note: If Galaxy Note 2 N7100 stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up, Home and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.

Click here to know How to Root Galaxy Note 2 N7100 running on Android 4.1.2 XXDMD2 Jelly Bean firmware.

Thanks for Read How to Update Galaxy Note 2 N7100 with Android 4.1.2 XXDMD2 Jelly Bean Official Firmware Article

How to Root Galaxy S4 I9505 on Android 4.2.2 XXUBMG5 Jelly Bean Firmware

Are You Looking For How to Root Galaxy S4 I9505 on Android 4.2.2 XXUBMG5 Jelly Bean Firmware

Samsung recently released its latest Android 4.2.2 Jelly Bean update with firmware build number I9505XXUBMG5 for the Snapdragon variant of Samsung Galaxy S4 with model number GT-I9505.

Samsung Galaxy S4 I9505 users who have already updated their devices with Android 4.2.2 XXUBMG5 Jelly Bean, may root their devices using the tutorial below.

This tutorial uses CF-Auto-Root file released by recognised XDA Developers, Chainfire. The CF-Auto-Root file allowing Galaxy S4 users to root their devices easily without depending on the firmware. It completely supports Android 4.2.2 Jelly Bean and future firmware as well. Head over to the CF-Auto-Root main thread to learn more about the root method.

Note: Using this root increases your flash counter. The flash counter keeps track of how many custom firmwares you have flashed, as this voids warranty. Triangle Away can be used to reset the flash counter after installing CF-Auto-Root.

Disclaimer: Rooting voids the warranty of your device. We and the developer of this rooting procedures shall not be held responsible if any undesirable outcomes may happen to your device. use of this root guide is solely at your own risk!

Pre-requisites
1. Install USB Drivers for Samsung Galaxy S4 I9505 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy S4 I9505 should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 per cent.
6. The CF-Auto-Root file works only on Samsung Galaxy S4 I9505. Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy S4 by navigating to Settings >> About Phone.

File Required
1. CF-Auto-Root for Galaxy S4 I9505 (CF-Auto-Root-jflte-jfltexx-gti9505.zip)
2. Odin 3.07

Steps to Root Galaxy S4 I9505 Running on Android 4.2.2 Jelly Bean Firmware
Step 1: Extract CF-Auto-Root and Odin 3.07 files using winrar/7zip/winzip or any other extracting tool.
Step 2: Switch off the Galaxy S4. Then boot the device into Download Mode by pressing and holding Volume Down, Home and Power buttons together until a construction Android robot icon with a warning triangle appears on screen. Now press the Volume Up button to enter Download Mode.
Step 3: Launch Odin on the computer as an Administrator.
Step 4: Connect the Galaxy S4 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn blue with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.
Note: If the Added message does not appear, then try re-install USB drivers or changing the port on the computer.
Step 5: In Odin, click the PDA button and select the CF-Auto-Root-jflte-jfltexx-gti9505.tar.md5 file.
Step 6: Verify that Auto Reboot and F.Reset Time checkboxes are selected in Odin. Also, ensure the Re-Partition option is not selected.
Step 7: Double-check and click Start in Odin. The installation process will now begin.
Step 8: Once the installation process is completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy S4 I9505 running on Android 4.2.2 XXUBMG5 Jelly Bean firmware is now rooted successfully. You can now install any app that requires root permission. Verify the root status of the device by downloading Root Checker app from Google Play Store.

Thank's to all fellas at XDA who first tried out this rooting technique. This method was originally posted via XDA-Developers original thread.

Click here to know How to Update Galaxy S4 I9505 with official Android 4.2.2 XXUBMG5 Jelly Bean firmware.

Thanks for Read How to Root Galaxy S4 I9505 on Android 4.2.2 XXUBMG5 Jelly Bean Firmware Article

How to Update Galaxy S4 (Canadian) SGH-I337M with Android 4.2.2 VLUAMG1 Jelly Bean Official Firmware

Are You Looking For How to Update Galaxy S4 (Canadian) SGH-I337M with Android 4.2.2 VLUAMG1 Jelly Bean Official Firmware

Samsung has just started to roll out a new software update based on Android 4.2.2 Jelly Bean with firmware build number I337MVLUAMG1 for the Canadian owners of Samsung Galaxy S4 with model number SGH-I337M. The new official firmware is currently available as an Over-The-Air (OTA) update as well as through Samsung KIES.

Firmware details
PDA: I337MVLUAMG1
CSC: I337MOYAAMG1
MODEM: I337MVLUAMG1
Version: Android 4.2.2
Built date: Jul 01, 2013
Regions: Canada
Carriers: Rogers, Bell, Telus, Virgin Mobile, Koodo, Fido, SaskTel

Samsung Galaxy S4 (Canadian) SGH-I337M users who missed the OTA update notification or unable to access the update over Samsung KIES, may follow our step-by-step guide to install the update manually.

Pre-requisites
1. Install USB Drivers for Samsung Galaxy S4 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. Ensure the battery of the phone is charged more than 80 per cent.
5. The Android 4.2.2 VLUAMG1 Jelly Bean firmware is compatible only with Samsung Galaxy S4 (Canadian) SGH-I337M. Applying these to any incorrect variant might brick the device. Verify the model number of the Galaxy S4 by navigating to Settings >> About Phone.

File Required
1. Android 4.2.2 VLUAMG1 Jelly Bean Firmware for Galaxy S4 (Canadian) SGH-I337M
2. Odin 3.07

Steps to Update Galaxy S4 (Canadian) SGH-I337M with Android 4.2.2 VLUAMG1 Jelly Bean Firmware
Step 1: Extract Firmware zip file that you downloaded already from above link using winrar/7zip/winzip or any other extracting tool, you will get a .tar.md5 file and some other files.
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Power off your phone. Wait 5-6 seconds for vibration to confirm complete switch off.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down, Home and Power buttons together until a construction Android robot icon with a warning triangle appears on screen. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy S4 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn blue with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.
Note: If the Added message does not appear, then try re-install USB drivers or changing the port on the computer.
Step 7: Choose the following files in Odin from extracted I337MVLUAMG1 firmware folder by using respective checkboxes:

• Select the PDA checkbox, and choose the file named .tar or .md5.
• Click the Phone checkbox, and choose the file with 'modem' in its name (ignore if there is no such file)
• Click the CSC checkbox, and select the file with 'csc' in its name (ignore if such file is missing)
• Choose the PIT checkbox, and choose the .pit file. Use only the file obtained during extracting in step 1 above, otherwise ignore it.

Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the START button to begin the installation process.
Step 10: Once the installation process is completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy S4 (Canadian) SGH-I337M should be now updated with official Android 4.2.2 VLUAMG1 Jelly Bean. Head over to Settings >> About Phone to verify the software version running on the device.

Note: If Galaxy S4 (Canadian) SGH-I337M stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up, Home and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.

Click here to know How to Root Galaxy S4 (Canadian) SGH-I337M running on Android 4.2.2 VLUAMG1 Jelly Bean firmware.

Thanks for Read How to Update Galaxy S4 (Canadian) SGH-I337M with Android 4.2.2 VLUAMG1 Jelly Bean Official Firmware Article

How to Root Galaxy Note 2 N7100 on Android 4.1.2 XXDMD2 Jelly Bean Firmware

Are You Looking For How to Root Galaxy Note 2 N7100 on Android 4.1.2 XXDMD2 Jelly Bean Firmware

Samsung Galaxy Note 2 N7100 users who have already updated their devices with Android 4.1.2 XXDMD2 Jelly Bean firmware, may root their devices using the tutorial below.

This tutorial uses CF-Auto-Root file released by recognised XDA Developers, Chainfire. The CF-Auto-Root file allowing Galaxy Note 2 users to root their devices easily without depending on the firmware. It completely supports Android 4.1.2 Jelly Bean and future firmware as well.

Disclaimer: Rooting voids the warranty of your device. We and the developer of this rooting procedures shall not be held responsible if any undesirable outcomes may happen to your device. use of this root guide is solely at your own risk!

Pre-requisites
1. Install USB Driver for Samsung Galaxy Note on the computer.
2. Enable USB Debugging Mode on the phone.
3. Make a backup of all your important data before following the guide.
4. The Galaxy Note 2 should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 per cent.
6. The CF-Auto-Root file works only on Samsung Galaxy Note 2 N7100. Applying this on any incorrect variant will brick the device. Verify the model number of the Galaxy Note 2 by navigating to Settings >> About Phone.

File Required
1. CF-Auto-Root for Galaxy Note 2 N7100  (CF-Auto-Root-t03g-t03gxx-gtn7100.zip)
2. Odin 3.07

Steps to Root Galaxy Note 2 N7100 on Android 4.1.2 XXDMD2 Jelly Bean
Step 1: Extract downloaded CF-Auto-Root zip file and you will find a .tar.md5 file within it.
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Power off your phone. Wait 5-6 seconds for vibration to confirm complete switch off.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy Note 2 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added. If Odin fails to detect the device then re-install USB driver.
Step 7: Select these files in Odin at respective buttons:

• Click the PDA Button, and select CF-Auto-Root-t03g-t03gxx-gtn7100.tar.md5.

Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the START button to begin the flashing process.
Step 10: Once flashing completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Your Samsung Galaxy Note 2 N7100 running on Android 4.1.2 XXDMD2 Jelly Bean firmware is now rooted successfully. You may now install any app that requires root permission.

Thank's to all fellas at XDA who first tried out this rooting technique. This root method was originally posted via XDA-Developers original thread.

Thanks for Read How to Root Galaxy Note 2 N7100 on Android 4.1.2 XXDMD2 Jelly Bean Firmware Article

How to Update Galaxy S Advance I9070 with Android 4.1.2 DXAMD1 Jelly Bean Official Firmware

Are You Looking For How to Update Galaxy S Advance I9070 with Android 4.1.2 DXAMD1 Jelly Bean Official Firmware

Samsung has rolled out official update, Android 4.1.2 Jelly Bean with base firmware DXAMD1, for the international version of Galaxy S Advance bearing model number I9070. This update is currently available for installation via OTA and Samsung KIES in supported Southeast Asia countries including Indonesia, Malaysia, Philippines, Singapore, Vietnam, and Thailand.

Firmware details
PDA: I9070DXAMD1
CSC: I9070OLBAMD3
Version: Android 4.1.2
Built date: April, 2013
Regions: Indonesia, Malaysia, Philippines, Singapore, Vietnam, Thailand

The Galaxy S Advance users who fail to upgrade their devices with Android 4.1.2 DXAMD1 Jelly Bean using official method for being region specific, may follow our step-by-step guide to install the update manually.

Pre-requisites
1. Install USB Driver for Samsung Galaxy S Advance on the computer.
2. Enable USB Debugging Mode.
3. Make a backup of all your important data before following the guide.
4. The Galaxy S Advance should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 per cent.
6. The Android 4.1.2 DXAMD1 Jelly Bean firmware is compatible only with Samsung Galaxy S Advance I9070 and installing this on any incorrect variant will brick the device. Therefore, verify the model number of the Galaxy S Advance by navigating to Settings >> About Phone.

File Required
1. Android 4.1.2 DXAMD1 Jelly Bean Firmware
2. Odin 3.07

Steps to Update Galaxy S Advance I9070 on Android 4.1.2 DXAMD1 Jelly Bean Firmware
Step 1: Extract Firmware zip file that you downloaded already from above link, you will get a .tar.md5 file and some other files.
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Power off your phone. Wait 5-6 seconds for vibration to confirm complete switch off.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy S Advance to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added. If Odin fails to detect the device then re-install USB driver.
Step 7: Choose the following files in Odin from extracted I9070DXAMD1 firmware folder by using respective checkboxes:

• Select the PDA checkbox, and choose the file named .tar or .md5.
• Click the Phone checkbox, and choose the file with 'modem' in its name (ignore if there is no such file)
• Click the CSC checkbox, and select the file with 'csc' in its name (ignore if such file is missing)
• Choose the PIT checkbox, and choose the .pit file. Use only the file obtained during extracting in step 1 above, otherwise ignore it.

Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the START button to begin the flashing process.
Step 10: Once flashing completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy S Advance I9070 should be now updated with official Android 4.1.2 DXAMD1 Jelly Bean. Head over to Settings >> About Phone to verify the software version running on the device.

Note: If Galaxy S Advance I9070 stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up, Home and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.

Click here to know How to Root Galaxy S Advance I9070 running on Android 4.1.2 DXAMD1 Jelly Bean firmware.

Thanks for Read How to Update Galaxy S Advance I9070 with Android 4.1.2 DXAMD1 Jelly Bean Official Firmware Article

How to Root Galaxy S4 (Canadian) SGH-I337M on Android 4.2.2 VLUAMG1 Jelly Bean Firmware

Are You Looking For How to Root Galaxy S4 (Canadian) SGH-I337M on Android 4.2.2 VLUAMG1 Jelly Bean Firmware

Canadian owners of the Samsung Galaxy S4 (SGH-I337M) has received a new software update based on Android 4.2.2 Jelly Bean with firmware build number I337MVLUAMG1.

Samsung Galaxy S4 (Canadian) SGH-I337M users who have already updated their devices with Android 4.2.2 VLUAMG1 Jelly Bean, may root their devices using the tutorial below.

This tutorial uses CF-Auto-Root file released by recognised XDA Developers, Chainfire. The CF-Auto-Root file allowing Galaxy S4 users to root their devices easily without depending on the firmware. It completely supports Android 4.2.2 Jelly Bean and future firmware as well. Head over to the CF-Auto-Root main thread to learn more about the root method.

Note: Using this root increases your flash counter. The flash counter keeps track of how many custom firmwares you have flashed, as this voids warranty. Triangle Away can be used to reset the flash counter after installing CF-Auto-Root.

Disclaimer: Rooting voids the warranty of your device. We and the developer of this rooting procedures shall not be held responsible if any undesirable outcomes may happen to your device. use of this root guide is solely at your own risk!

Pre-requisites
1. Install USB Drivers for Samsung Galaxy S4 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy S4 should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 per cent.
6. The CF-Auto-Root file works only on Samsung Galaxy S4 (Canadian) SGH-I337M. Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy S4 by navigating to Settings >> About Phone.

File Required
1. CF-Auto-Root for Galaxy S4 (Canadian) SGH-I337M (CF-Auto-Root-jfltecan-jfltevl-sghi337m.zip)
2. Odin 3.07

Steps to Root Galaxy S4 (Canadian) SGH-I337M Running on Android 4.2.2 VLUAMG1 Jelly Bean Firmware
Step 1: Extract CF-Auto-Root and Odin 3.07 files using winrar/7zip/winzip or any other extracting tool.
Step 2: Switch off the Galaxy S4. Then boot the device into Download Mode by pressing and holding Volume Down, Home and Power buttons together until a construction Android robot icon with a warning triangle appears on screen. Now press the Volume Up button to enter Download Mode.
Step 3: Launch Odin on the computer as an Administrator.
Step 4: Connect the Galaxy S4 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn blue with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.
Note: If the Added message does not appear, then try re-install USB drivers or changing the port on the computer.
Step 5: In Odin, click the PDA button and select the CF-Auto-Root-jfltecan-jfltevl-sghi337m.tar.md5 file.
Step 6: Verify that Auto Reboot and F.Reset Time checkboxes are selected in Odin. Also, ensure the Re-Partition option is not selected.
Step 7: Double-check and click Start in Odin. The installation process will now begin.
Step 8: Once the installation process is completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy S4 (Canadian) SGH-I337M running on Android 4.2.2 VLUAMG1 Jelly Bean firmware is now rooted successfully. You can now install any app that requires root permission. Verify the root status of the device by downloading Root Checker app from Google Play Store.

Thank's to all fellas at XDA who first tried out this rooting technique. This method was originally posted via XDA-Developers original thread.

Click here to know How to Update Galaxy S4 (Canadian) SGH-I337M with official Android 4.2.2 VLUAMG1 Jelly Bean firmware.

Thanks for Read How to Root Galaxy S4 (Canadian) SGH-I337M on Android 4.2.2 VLUAMG1 Jelly Bean Firmware Article

How to Root Galaxy S Advance I9070 on Android 4.1.2 DXAMD1 Jelly Bean Firmware

Are You Looking For How to Root Galaxy S Advance I9070 on Android 4.1.2 DXAMD1 Jelly Bean Firmware

Samsung recently rolled out its latest official Android 4.1.2 DXAMD1 Jelly Bean firmware for Galaxy S Advance I9070 in several countries. The official firmware is now available for download via Over-The-Air (OTA) update as well as through Samsung KIES.

Samsung Galaxy S Advance I9070 users who have already updated their devices with Android 4.1.2 DXAMD1 Jelly Bean firmware, may root their devices using the tutorial below.

Disclaimer: Rooting voids the warranty of your device. We and the developer of this rooting procedures shall not be held responsible if any undesirable outcomes may happen to your device. use of this root guide is solely at your own risk!

Pre-requisites
1. Install USB Driver for Samsung Galaxy S Advance on the computer.
2. Enable USB Debugging Mode on the phone.
3. Make a backup of all your important data before following the guide.
4. The Galaxy S Advance should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 per cent.
6. The root file works only on Samsung Galaxy S Advance I9070 running on Android 4.1.2 DXAMD1 Jelly Bean firmware. Applying this on any incorrect variant will brick the device. Verify the model number of the Galaxy S Advance by navigating to Settings >> About Phone.

Steps to Root Galaxy S Advance I9070 on Android 4.1.2 DXAMD1 Jelly Bean
Step 1: Download Jelly Bean Root Package for Samsung Galaxy S Advance to the computer.
Step 2: Connect the phone to the computer using USB cable.
Step 3: Copy the downloaded root.zip file to the external SD card of the phone.
Step 4: Unplug the USB cable from the phone to disconnect it from the computer and then turn it off
Step 5: Boot the Galaxy S Advance into stock recovery mode by pressing and holding Volume Up, Home and Power buttons together until the device turns on. In the recovery mode, use the Volume keys to scroll between the options and the Power button to select the desired option.
Step 6: Navigate to and select install update from external sdcard then select choose zip from sdcard. Then browse to the root.zip file which was earlier copied to the SD card
Step 7: Select the root.zip file and confirm installation. The flashing process should start now.
Step 8: When the installation process is completed, reboot the phone by selecting reboot system now from recovery menu.

Once the Samsung Galaxy S Advance boots up, it should be rooted successfully on Android 4.1.2 DXAMD1 Jelly Bean official firmware. You may now install any app that requires root permission.

Thank's to all fellas at XDA who first tried out this rooting technique. This root method was originally posted via XDA-Developers original thread.

Thanks for Read How to Root Galaxy S Advance I9070 on Android 4.1.2 DXAMD1 Jelly Bean Firmware Article

How to Root Galaxy S3 (LTE) I9305/T/N on Android 4.1.2 Jelly Bean Firmware

Are You Looking For How to Root Galaxy S3 (LTE) I9305/T/N on Android 4.1.2 Jelly Bean Firmware

Samsung has released its latest Android 4.1.2 Jelly Bean firmware update on the LTE variant of Samsung Galaxy S3 bearing model number GT-I9305/T/N in several countries. The new official firmware is now available for download via Over-The-Air (OTA) update as well as through Samsung KIES.

Samsung Galaxy S3 (LTE) I9305/T/N users who have already updated their devices with Android 4.1.2 Jelly Bean, may root their devices using the tutorial below.

This tutorial uses CF-Auto-Root file released by recognised XDA Developers, Chainfire. The CF-Auto-Root file allowing Galaxy S3 users to root their devices easily without depending on the firmware. It completely supports Android 4.1.2 Jelly Bean and future firmware as well. Head over to the CF-Auto-Root main thread to learn more about the root method.

Disclaimer: Rooting voids the warranty of your device. We and the developer of this rooting procedures shall not be held responsible if any undesirable outcomes may happen to your device. use of this root guide is solely at your own risk!

Pre-requisites
1) Install USB Driver for Samsung Galaxy S3 on the computer.
2) Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options (Android 4.0 or later) or go to Settings >> Applications >> Development (Android 2.3 or earlier).
3) Make a backup of all your important data before following the guide.
4) Ensure the battery of the phone is charged more than 80 per cent.
5) The CF-Auto-Root file works only on Samsung Galaxy S3 (LTE) I9305/T/N. Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy S3 by navigating to Settings >> About Phone.

File Required
1. CF-Auto-Root for Galaxy S3 (LTE) GT-I9305 (CF-Auto-Root-m3-m3zh-gti9305.zip), GT-I9305T (CF-Auto-Root-m3-m3dv-gti9305t.zip), or GT-I9305N (CF-Auto-Root-m3-m3swexx-gti9305n.zip)
2. Odin 3.07

Steps to Root Galaxy S3 (LTE) I9305/T/N Running on Android 4.1.2 Jelly Bean Firmware
Step 1: Extract CF-Auto-Root and Odin 3.07 files using winrar/7zip/winzip or any other extracting tool.
Step 2: Switch off the Galaxy S3. Then boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 3: Launch Odin on the computer.
Step 4: Connect the Galaxy S3 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added. If Odin fails to detect the device then re-install USB driver
Step 5: In Odin, click the PDA button and select the CF-Auto-Root with a .tar.md5 file.
Step 6: Verify that Auto Reboot and F.Reset Time checkboxes are selected in Odin. Also, ensure the Re-Partition option in Odin is NOT selected.
Step 7: Double-check and click Start in Odin. The installation process will now begin.
Step 8: Once flashing completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy S3 (LTE) I9305/T/N running on Android 4.1.2 Jelly Bean firmware is now rooted successfully. You can now install any app that requires root permission. Verify the root status of the device by downloading Root Checker app from Google Play Store.

Thank's to all fellas at XDA who first tried out this rooting technique. This method was originally posted via XDA-Developers original thread.

Thanks for Read How to Root Galaxy S3 (LTE) I9305/T/N on Android 4.1.2 Jelly Bean Firmware Article

How to Root Galaxy S4 I9505 on Android 4.2.2 XXUBMGA Jelly Bean Firmware

Are You Looking For How to Root Galaxy S4 I9505 on Android 4.2.2 XXUBMGA Jelly Bean Firmware

The LTE variant of Samsung Galaxy S4 (GT-I9505) recently received a new software update with firmware build number I9505XXUBMGA. The new software update is still based on Android 4.2.2 Jelly Bean version and now available in Germany, Spain, and Nordic countries.

Samsung Galaxy S4 I9505 users who have already updated their devices with Android 4.2.2 XXUBMGA Jelly Bean, may root their devices using the tutorial below.

This tutorial uses CF-Auto-Root file released by recognised XDA Developers, Chainfire. The CF-Auto-Root file allowing Galaxy S4 users to root their devices easily without depending on the firmware. It completely supports Android 4.2.2 Jelly Bean and future firmware as well. Head over to the CF-Auto-Root main thread to learn more about the root method.

Note: Using this root increases your flash counter. The flash counter keeps track of how many custom firmwares you have flashed, as this voids warranty. Triangle Away can be used to reset the flash counter after installing CF-Auto-Root.

Disclaimer: Rooting voids the warranty of your device. We and the developer of this rooting procedures shall not be held responsible if any undesirable outcomes may happen to your device. use of this root guide is solely at your own risk!

Pre-requisites
1. Install USB Drivers for Samsung Galaxy S4 I9505 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy S4 I9505 should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 per cent.
6. The CF-Auto-Root file works only on Samsung Galaxy S4 I9505. Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy S4 by navigating to Settings >> About Phone.

File Required
1. CF-Auto-Root for Galaxy S4 I9505 (CF-Auto-Root-jflte-jfltexx-gti9505.zip)
2. Odin 3.07

Steps to Root Galaxy S4 I9505 Running on Android 4.2.2 XXUBMGA Jelly Bean Firmware
Step 1: Extract CF-Auto-Root and Odin 3.07 files using winrar/7zip/winzip or any other extracting tool.
Step 2: Switch off the Galaxy S4. Then boot the device into Download Mode by pressing and holding Volume Down, Home and Power buttons together until a construction Android robot icon with a warning triangle appears on screen. Now press the Volume Up button to enter Download Mode.
Step 3: Launch Odin on the computer as an Administrator.
Step 4: Connect the Galaxy S4 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn blue with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.
Note: If the Added message does not appear, then try re-install USB drivers or changing the port on the computer.
Step 5: In Odin, click the PDA button and select the CF-Auto-Root-jflte-jfltexx-gti9505.tar.md5 file.
Step 6: Verify that Auto Reboot and F.Reset Time checkboxes are selected in Odin. Also, ensure the Re-Partition option is not selected.
Step 7: Double-check and click Start in Odin. The installation process will now begin.
Step 8: Once the installation process is completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy S4 I9505 running on Android 4.2.2 XXUBMGA Jelly Bean firmware is now rooted successfully. You can now install any app that requires root permission. Verify the root status of the device by downloading Root Checker app from Google Play Store.

Thank's to all fellas at XDA who first tried out this rooting technique. This method was originally posted via XDA-Developers original thread.

Click here to know How to Update Galaxy S4 I9505 with official Android 4.2.2 XXUBMGA Jelly Bean firmware.

Thanks for Read How to Root Galaxy S4 I9505 on Android 4.2.2 XXUBMGA Jelly Bean Firmware Article

How to Update Galaxy S4 I9505 with Android 4.2.2 XXUBMGA Jelly Bean Official Firmware

Are You Looking For How to Update Galaxy S4 I9505 with Android 4.2.2 XXUBMGA Jelly Bean Official Firmware

Samsung recently released a new Android 4.2.2 Jelly Bean update with base firmware XXUBMGA for the owners of Samsung Galaxy S4 (GT-I9505) in Germany, Spain, and Nordic countries. The new official firmware is now available as an Over-The-Air (OTA) update as well as through Samsung KIES.

Firmware details
PDA: I9505XXUBMGA
CSC: I9505OXABMGA
MODEM: I9505XXUBMGA
Version: Android 4.2.2
Built date: Jul 11, 2013
Regions: Germany, Spain, Nordic countries

Samsung Galaxy S4 I9505 users who missed the OTA update notification or unable to access the update over Samsung KIES, may follow our step-by-step guide to install the update manually.

Pre-requisites
1. Install USB Drivers for Samsung Galaxy S4 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy S4 should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 per cent.
6. The Android 4.2.2 XXUBMGA Jelly Bean firmware is compatible only with Samsung Galaxy S4 I9505. Applying these to any incorrect variant might brick the device. Verify the model number of the Galaxy S4 by navigating to Settings >> About Phone.

File Required
1. Android 4.2.2 XXUBMGA Jelly Bean Firmware for Samsung Galaxy S4 I9505
2. Odin 3.07

Steps to Update Galaxy S4 I9505 with Android 4.2.2 XXUBMGA Jelly Bean Firmware
Step 1: Extract Firmware zip file that you downloaded already from above link using winrar/7zip/winzip or any other extracting tool, you will get a .tar.md5 file and some other files.
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Power off your phone. Wait 5-6 seconds for vibration to confirm complete switch off.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down, Home and Power buttons together until a construction Android robot icon with a warning triangle appears on screen. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy S4 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn blue with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.
Note: If the Added message does not appear, then try re-install USB drivers or changing the port on the computer.
Step 7: Choose the following files in Odin from extracted I9505XXUBMGA firmware folder by using respective checkboxes:

• Select the PDA checkbox, and choose the file named .tar or .md5.
• Click the Phone checkbox, and choose the file with 'modem' in its name (ignore if there is no such file)
• Click the CSC checkbox, and select the file with 'csc' in its name (ignore if such file is missing)
• Choose the PIT checkbox, and choose the .pit file. Use only the file obtained during extracting in step 1 above, otherwise ignore it.

Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the START button to begin the installation process.
Step 10: Once the installation process is completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy S4 I9505 should be now updated with official Android 4.2.2 XXUBMGA Jelly Bean. Head over to Settings >> About Phone to verify the software version running on the device.

Note: If Galaxy S4 I9505 stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up, Home and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.

Click here to know How to Root Galaxy S4 I9505 running on Android 4.2.2 XXUBMGA Jelly Bean firmware.

Thanks for Read How to Update Galaxy S4 I9505 with Android 4.2.2 XXUBMGA Jelly Bean Official Firmware Article