How to Root Galaxy Note 2 (Canadian) SGH-I317M on Android 4.1.2 Jelly Bean Firmware

Are You Looking For How to Root Galaxy Note 2 (Canadian) SGH-I317M on Android 4.1.2 Jelly Bean Firmware

Samsung Galaxy Note 2 (Canadian) SGH-I317M users who have already updated their devices with Android 4.1.2 Jelly Bean, may root their devices using the tutorial below.

This tutorial uses CF-Auto-Root file released by recognised XDA Developers, Chainfire. The CF-Auto-Root file allowing Galaxy Note 2 users to root their devices easily without depending on the firmware. It completely supports Android 4.1.2 Jelly Bean and future firmware as well. Head over to the CF-Auto-Root main thread to learn more about the root method.

Note: Using this root increases your flash counter. The flash counter keeps track of how many custom firmwares you have flashed, as this voids warranty. Triangle Away can be used to reset the flash counter after installing CF-Auto-Root.

Disclaimer: Rooting voids the warranty of your device. We and the developer of this rooting procedures shall not be held responsible if any undesirable outcomes may happen to your device. use of this root guide is solely at your own risk!

Pre-requisites
1. Install USB Driver for Samsung Galaxy Note 2 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. Ensure the battery of the phone is charged more than 80 per cent.
5. The CF-Auto-Root file works only on Samsung Galaxy Note 2 (Canadian) SGH-I317M. Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy Note 2 by navigating to Settings >> About Phone.

File Required
1. CF-Auto-Root for Galaxy Note 2 (Canadian) SGH-I317M (CF-Auto-Root-t0ltecan-t0ltevl-sghi317m.zip)
2. Odin 3.07

Steps to Galaxy Note 2 (Canadian) SGH-I317M Running on Android 4.1.2 Jelly Bean Firmware
Step 1: Extract CF-Auto-Root and Odin 3.07 files using winrar/7zip/winzip or any other extracting tool.
Step 2: Switch off the Galaxy Note 2. Then boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 3: Launch Odin on the computer.
Step 4: Connect the Galaxy Note 2 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.
Step 5: In Odin, click the PDA button and select the CF-Auto-Root-t0ltecan-t0ltevl-sghi317m.tar.md5 file.
Step 6: Verify that Auto Reboot and F.Reset Time checkboxes are selected in Odin. Also, ensure the Re-Partition option in Odin is not selected.
Step 7: Double-check and click Start in Odin. The installation process will now begin.
Step 8: Once the installation process is completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy Note 2 (Canadian) SGH-I317M running on Android 4.1.2 Jelly Bean firmware is now rooted successfully. You can now install any app that requires root permission. Verify the root status of the device by downloading Root Checker app from Google Play Store.

Thanks for Read How to Root Galaxy Note 2 (Canadian) SGH-I317M on Android 4.1.2 Jelly Bean Firmware Article

How to Update Galaxy S3 (Canadian) SGH-I747M with Android 4.1.2 VLDMF1 Jelly Bean Official Firmware

Are You Looking For How to Update Galaxy S3 (Canadian) SGH-I747M with Android 4.1.2 VLDMF1 Jelly Bean Official Firmware

Samsung has delivered a new software update based on Android 4.1.2 Jelly Bean with build number I747MVLDMF1 for the North American owners of Samsung Galaxy S3 bearing model number SGH-I747M - Rogers, Bell, Telus, and SaskTel.

Firmware details
PDA: I747MVLDMF1
CSC: I747MOYBDMF1
MODEM: I747MVLDMF1
Version: Android 4.1.2
Built date: Jun 3, 2013
Regions: Canada

The new official firmware is currently available as an Over-The-Air (OTA) update as well as through Samsung KIES. However, those who missed the OTA update notification or unable to access the update over Samsung KIES can download and install the same manually, using our step-by-step guide.

Pre-requisites
1. Install USB Driver for Samsung Galaxy S3 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. Ensure the battery of the phone is charged more than 80 per cent.
5. The Android 4.1.2 VLDMF1 Jelly Bean firmware is compatible only with Galaxy S3 (Canadian) SGH-I747M. Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy S3 by navigating to Settings >> About Phone.

File Required
1. Android 4.1.2 VLDMF1 Jelly Bean Firmware for Galaxy S3 SGH-I747M
2. Odin 3.07

Steps to Update Galaxy S3 SGH-I747M with Android 4.1.2 VLDMF1 Jelly Bean Firmware
Step 1: Extract Firmware zip file that you downloaded already from above link using winrar/7zip/winzip or any other extracting tool, you will get a .tar.md5 file and some other files.
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Power off your phone. Wait 5-6 seconds for vibration to confirm complete switch off.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy S3 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.
Step 7: Choose the following files in Odin from extracted I747MVLDMF1 firmware folder by using respective checkboxes:

• Select the PDA checkbox, and choose the file named .tar or .md5.
• Click the Phone checkbox, and choose the file with 'modem' in its name (ignore if there is no such file)
• Click the CSC checkbox, and select the file with 'csc' in its name (ignore if such file is missing)
• Choose the PIT checkbox, and choose the .pit file. Use only the file obtained during extracting in step 1 above, otherwise ignore it.

Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the START button to begin the installation process.
Step 10: Once the installation process is completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy S3 SGH-I747M should be now updated with official Android 4.1.2 VLDMF1 Jelly Bean firmware. Head over to Settings >> About Phone to verify the software version running on the device.

Note: If Galaxy S3 SGH-I747M stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up, Home and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.

Click here to know How to Root Galaxy S3 (Canadian) SGH-I747M running on Android 4.1.2 VLDMF1 Jelly Bean firmware.

Thanks for Read How to Update Galaxy S3 (Canadian) SGH-I747M with Android 4.1.2 VLDMF1 Jelly Bean Official Firmware Article

How to Root Galaxy S3 (Canadian) SGH-I747M on Android 4.1.2 Jelly Bean Firmware

Are You Looking For How to Root Galaxy S3 (Canadian) SGH-I747M on Android 4.1.2 Jelly Bean Firmware

Samsung has just started to roll out Android 4.1.2 Jelly Bean update for the North American versions of Samsung Galaxy S3 with model number SGH-I747M.

Samsung Galaxy S3 SGH-I747M users who have already updated their devices with Android 4.1.2 Jelly Bean, may root their devices using the tutorial below.

This tutorial uses CF-Auto-Root file released by recognised XDA Developers, Chainfire. The CF-Auto-Root file allowing Galaxy S3 users to root their devices easily without depending on the firmware. It completely supports Android 4.1.2 Jelly Bean and future firmware as well. Head over to the CF-Auto-Root main thread to learn more about the root method.

Disclaimer: Rooting voids the warranty of your device. We and the developer of this rooting procedures shall not be held responsible if any undesirable outcomes may happen to your device. use of this root guide is solely at your own risk!

Pre-requisites
1) Install USB Driver for Samsung Galaxy S3 on the computer.
2) Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3) Make a backup of all your important data before following the guide.
4) Ensure the battery of the phone is charged more than 80 per cent.
5) The CF-Auto-Root file works only on Samsung Galaxy S3 SGH-I747M. Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy S3 by navigating to Settings >> About Phone.

File Required
1. CF-Auto-Root for Galaxy S3 SGH-I747M (CF-Auto-Root-d2can-d2vl-sghi747m.zip)
2. Odin 3.07

Steps to Root Galaxy S3 SGH-I747M Running on Android 4.1.2 Jelly Bean Firmware
Step 1: Extract CF-Auto-Root and Odin 3.07 files using winrar/7zip/winzip or any other extracting tool.
Step 2: Switch off the Galaxy S3. Then boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 3: Launch Odin on the computer.
Step 4: Connect the Galaxy S3 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added. If Odin fails to detect the device then re-install USB drivers.
Step 5: In Odin, click the PDA button and select the CF-Auto-Root-d2can-d2vl-sghi747m.tar.md5 file.
Step 6: Verify that Auto Reboot and F.Reset Time checkboxes are selected in Odin. Also, ensure the Re-Partition option in Odin is not selected.
Step 7: Double-check and click Start in Odin. The installation process will now begin.
Step 8: Once flashing completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy S3 SGH-I747M running on Android 4.1.2 Jelly Bean firmware is now rooted successfully. You can now install any app that requires root permission. Verify the root status of the device by downloading Root Checker app from Google Play Store.

Thank's to all fellas at XDA who first tried out this rooting technique. This method was originally posted via XDA-Developers original thread.

Click here to know How to Update Galaxy S3 (Canadian) SGH-I747M with Android 4.1.2 VLDMF1 Jelly Bean official firmware.

Thanks for Read How to Root Galaxy S3 (Canadian) SGH-I747M on Android 4.1.2 Jelly Bean Firmware Article

How to Root Galaxy S4 (U.S. Cellular) SCH-R970 on Android 4.2.2 VXUAMDL Jelly Bean Firmware

Are You Looking For How to Root Galaxy S4 (U.S. Cellular) SCH-R970 on Android 4.2.2 VXUAMDL Jelly Bean Firmware

Samsung Galaxy S4 (U.S. Cellular) SCH-R970 users who have already installed their devices with Android 4.2.2 VXUAMDL Jelly Bean, may root their devices using the tutorial below.

This tutorial uses CF-Auto-Root file released by recognised XDA Developers, Chainfire. The CF-Auto-Root file allowing Galaxy S4 (U.S. Cellular) users to root their devices easily without depending on the firmware. It completely supports Android 4.2.2 Jelly Bean and future firmware as well. Head over to the CF-Auto-Root main thread to learn more about the root method.

Note: Using this root increases your flash counter. The flash counter keeps track of how many custom firmwares you have flashed, as this voids warranty. Triangle Away can be used to reset the flash counter after installing CF-Auto-Root.

Disclaimer: Rooting voids the warranty of your device. We and the developer of this rooting procedures shall not be held responsible if any undesirable outcomes may happen to your device. use of this root guide is solely at your own risk!

Pre-requisites
1. Install USB Driver for Samsung Galaxy S4 the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. Ensure the battery of the phone is charged more than 80 per cent.
5. The CF-Auto-Root file works only on Samsung Galaxy S4 (U.S. Cellular) SCH-R970. Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy S4 by navigating to Settings >> About Phone.

File Required
1. CF-Auto-Root for Galaxy S4 (U.S. Cellular) SCH-R970 (CF-Auto-Root-jflteusc-jflteusc-schr970.zip)
2. Odin 3.07

Steps to Root Galaxy S4 (U.S. Cellular) SCH-R970 Running on Android 4.2.2 VXUAMDL Jelly Bean Firmware
Step 1: Extract CF-Auto-Root and Odin 3.07 files using winrar/7zip/winzip or any other extracting tool.
Step 2: Switch off the Galaxy S4. Then boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 3: Launch Odin on the computer.
Step 4: Connect the Galaxy S4 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.
Step 5: In Odin, click the PDA button and select the CF-Auto-Root-jflteusc-jflteusc-schr970.tar.md5 file.
Step 6: Verify that Auto Reboot and F.Reset Time checkboxes are selected in Odin. Also, ensure the Re-Partition option in Odin is not selected.
Step 7: Double-check and click Start in Odin. The installation process will now begin.
Step 8: Once the installation process is completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy S4 (U.S. Cellular) SCH-R970 running on Android 4.2.2 VXUAMDL Jelly Bean firmware is now rooted successfully. You can now install any app that requires root permission. Verify the root status of the device by downloading Root Checker app from Google Play Store.

Thanks for Read How to Root Galaxy S4 (U.S. Cellular) SCH-R970 on Android 4.2.2 VXUAMDL Jelly Bean Firmware Article

How to Update Galaxy Tab 2 10.1 (AT&T) SGH-I497 with Android 4.1.2 UCUAMF2 Jelly Bean Official Firmware

Are You Looking For How to Update Galaxy Tab 2 10.1 (AT&T) SGH-I497 with Android 4.1.2 UCUAMF2 Jelly Bean Official Firmware

Samsung has delivered a new software update for the AT&T subscribers of Samsung Galaxy Tab 2 10.1 with model number SGH-I497. This firmware update is a major release based on Android 4.1.2 Jelly Bean with build number I497UCUAMF2.

According to Samsung, the new official firmware reportedly brings a lot of new features and enhancements over its previous build.

Features Included:
- Customizable widgets
- Improved text input and spell-checking
- New dictionaries for better error correction and word suggestion
- Enhanced web browsing and personalization capability
- Improved email management
- New technology for better security options
- Google Now with enhanced voice activation

This update is currently available through Windows and Mac computers using the Samsung Kies software application.

How Do I Update My Samsung Galaxy Tab 2 10.1 (AT&T) SGH-I497?
Step-1: Start Samsung Kies, or if you have downloaded Samsung Kies, launch the installer and allow Kies to install on your system. If you are prompted to reboot the system, do so before proceeding.
Step-2: Connect your device to your PC or laptop using the supplied USB cable. Ensure that Kies recognizes your device by looking in the upper section of the left-bar navigation menu. Your device should be listed.
Step-3: Once Kies recognizes the device you will see the following pop-up. Follow the on-screen instructions to continue.

Android 4.1.2 Jelly Bean Update

Note: The time to upgrade your device will vary. Dependent upon your computer and network connection, you may experience some idle time or slow response in Kies. Do not close any programs on your PC, disconnect or turn off your device until the upgrade process is complete.

Step-4: Once the upgrading process is completed, your device will restart automatically. You can now disconnect your device from the PC.

Firmware Upgrade Completed

Samsung Galaxy Tab 2 10.1 (AT&T) SGH-I497 should be now updated with official Android 4.1.2 UCUAMF2 Jelly Bean firmware. Head over to Settings >> About Phone to verify the software version running on the device.

Click here to know How to Root Galaxy Tab 2 10.1 (AT&T) SGH-I497 running on Android 4.1.2 UCUAMF2 Jelly Bean firmware.

Thanks for Read How to Update Galaxy Tab 2 10.1 (AT&T) SGH-I497 with Android 4.1.2 UCUAMF2 Jelly Bean Official Firmware Article

How to Root Galaxy Tab 2 10.1 (AT&T) SGH-I497 on Android 4.1.2 UCUAMF2 Jelly Bean Firmware

Are You Looking For How to Root Galaxy Tab 2 10.1 (AT&T) SGH-I497 on Android 4.1.2 UCUAMF2 Jelly Bean Firmware

The AT&T subscribers of Samsung Galaxy Tab 2 10.1 bearing model number SGH-I497 recently received its latest Android 4.1.2 Jelly Bean firmware update with base firmware UCUAMF2. This update is currently available through Windows and Mac computers using the Samsung Kies software application.

Samsung Galaxy Tab 2 10.1 (AT&T) SGH-I497 users who have already updated their devices with Android 4.1.2 UCUAMF2 Jelly Bean, may root their devices using the tutorial below.

This tutorial uses CF-Auto-Root file released by recognised XDA Developers, Chainfire. The CF-Auto-Root file allowing Galaxy Tab 2 10.1 users to root their devices easily without depending on the firmware. It completely supports Android 4.1.2 Jelly Bean and future firmware as well. Head over to the CF-Auto-Root main thread to learn more about the root method.

Note: Using this root increases your flash counter. The flash counter keeps track of how many custom firmwares you have flashed, as this voids warranty. Triangle Away can be used to reset the flash counter after installing CF-Auto-Root.

Disclaimer: Rooting voids the warranty of your device. We and the developer of this rooting procedures shall not be held responsible if any undesirable outcomes may happen to your device. use of this root guide is solely at your own risk!

Pre-requisites
1. Install USB Driver for Samsung Galaxy Tab 2 10.1 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. Ensure the battery of the phone is charged more than 80 per cent.
5. The CF-Auto-Root file works only on Samsung Galaxy Tab 2 10.1 (AT&T) SGH-I497. Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy Tab 2 10.1 by navigating to Settings >> About Phone.

File Required
1. CF-Auto-Root for Galaxy Tab 2 10.1 (AT&T) SGH-I497 (CF-Auto-Root-espresso10att-espresso10uc-samsungsghi497.zip)
2. Odin 3.07

Steps to Root Galaxy Tab 2 10.1 (AT&T) SGH-I497 Running on Android 4.1.2 UCUAMF2 Jelly Bean Firmware
Step 1: Extract CF-Auto-Root and Odin 3.07 files using winrar/7zip/winzip or any other extracting tool.
Step 2: Switch off the Galaxy Tab 2 10.1. Then boot the device into Download Mode by pressing and holding Volume Down and Power button together until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 3: Launch Odin on the computer.
Step 4: Connect the Galaxy Tab 2 10.1 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added. If Odin fails to detect the device then re-install USB driver
Step 5: In Odin, click the PDA button and select the CF-Auto-Root-espresso10att-espresso10uc-samsungsghi497.tar.md5 file.
Step 6: Verify that Auto Reboot and F.Reset Time checkboxes are selected in Odin. Also, ensure the Re-Partition option in Odin is not selected.
Step 7: Double-check and click Start in Odin. The installation process will now begin.
Step 8: Once the installation process is completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy Tab 2 10.1 (AT&T) SGH-I497 running on Android 4.1.2 UCUAMF2 Jelly Bean firmware is now rooted successfully. You can now install any app that requires root permission. Verify the root status of the device by downloading Root Checker app from Google Play Store.

Thank's to all fellas at XDA who first tried out this rooting technique. This method was originally posted via XDA-Developers original thread.

Thanks for Read How to Root Galaxy Tab 2 10.1 (AT&T) SGH-I497 on Android 4.1.2 UCUAMF2 Jelly Bean Firmware Article

How to Update Galaxy S4 I9505 with Android 4.2.2 XXUBMF8 Jelly Bean Official Firmware

Are You Looking For How to Update Galaxy S4 I9505 with Android 4.2.2 XXUBMF8 Jelly Bean Official Firmware

Samsung has just started to roll out another Android 4.2.2 Jelly Bean update with base firmware XXUBMF8 for the owners of Samsung Galaxy S4 bearing model number GT-I9505 in Southeast Asia countries - Malaysia, Philippines, and Singapore. This official firmware is currently available as an Over-The-Air (OTA) update as well as through Samsung KIES.

Firmware details
PDA: I9505XXUBMF8
CSC: I9505OLBBMF8
MODEM: I9505DXUBMF8
Version: Android 4.2.2
Built date: Jun 19, 2013
Regions: Malaysia, Philippines, Singapore

Samsung Galaxy S4 I9505 users who missed the OTA update notification or unable to access the update over Samsung KIES, may follow our step-by-step guide to install the update manually.

Pre-requisites
1. Install USB Driver for Samsung Galaxy S4 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy S4 should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 per cent.
6. The Android 4.2.2 XXUBMF8 Jelly Bean firmware is compatible only with Samsung Galaxy S4 I9505. Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy S4 by navigating to Settings >> About Phone.

File Required
1. Android 4.2.2 XXUBMF8 Jelly Bean Firmware for Samsung Galaxy S4 I9505
2. Odin 3.07

Steps to Update Galaxy S4 I9505 with Android 4.2.2 XXUBMF8 Jelly Bean Firmware
Step 1: Extract Firmware zip file that you downloaded already from above link using winrar/7zip/winzip or any other extracting tool, you will get a .tar.md5 file and some other files.
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Power off your phone. Wait 5-6 seconds for vibration to confirm complete switch off.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy S4 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.
Step 7: Choose the following files in Odin from extracted I9505XXUBMF8 firmware folder by using respective checkboxes:

• Select the PDA checkbox, and choose the file named .tar or .md5.
• Click the Phone checkbox, and choose the file with 'modem' in its name (ignore if there is no such file)
• Click the CSC checkbox, and select the file with 'csc' in its name (ignore if such file is missing)
• Choose the PIT checkbox, and choose the .pit file. Use only the file obtained during extracting in step 1 above, otherwise ignore it.

Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the START button to begin the installation process.
Step 10: Once the installation process is completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy S4 I9505 should be now updated with official Android 4.2.2 XXUBMF8 Jelly Bean. Head over to Settings >> About Phone to verify the software version running on the device.

Note: If Galaxy S4 I9505 stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up, Home and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.

Click here to know How to Root Galaxy S4 I9505 running on Android 4.2.2 XXUBMF8 Jelly Bean firmware.

Thanks for Read How to Update Galaxy S4 I9505 with Android 4.2.2 XXUBMF8 Jelly Bean Official Firmware Article

How to Root Galaxy S4 I9505 on Android 4.2.2 XXUBMF8 Jelly Bean Firmware

Are You Looking For How to Root Galaxy S4 I9505 on Android 4.2.2 XXUBMF8 Jelly Bean Firmware

Samsung recently released another Android 4.2.2 Jelly Bean update with base firmware XXUBMF8 for the Snapdragon variant of Samsung Galaxy S4 bearing model number GT-I9505.

Samsung Galaxy S4 I9505 users who have already updated their devices with Android 4.2.2 XXUBMF8 Jelly Bean, may root their devices using the tutorial below.

This tutorial uses CF-Auto-Root file released by recognised XDA Developers, Chainfire. The CF-Auto-Root file allowing Galaxy S4 users to root their devices easily without depending on the firmware. It completely supports Android 4.2.2 Jelly Bean and future firmware as well. Head over to the CF-Auto-Root main thread to learn more about the root method.

Note: Using this root increases your flash counter. The flash counter keeps track of how many custom firmwares you have flashed, as this voids warranty. Triangle Away can be used to reset the flash counter after installing CF-Auto-Root.

Disclaimer: Rooting voids the warranty of your device. We and the developer of this rooting procedures shall not be held responsible if any undesirable outcomes may happen to your device. use of this root guide is solely at your own risk!

Pre-requisites
1. Install USB Driver for Samsung Galaxy S4 I9505 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy S4 I9505 should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 per cent.
6. The CF-Auto-Root file works only on Samsung Galaxy S4 I9505. Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy S4 by navigating to Settings >> About Phone.

File Required
1. CF-Auto-Root for Galaxy S4 I9505 (CF-Auto-Root-jflte-jfltexx-gti9505.zip)
2. Odin 3.07

Steps to Root Galaxy S4 I9505 Running on Android 4.2.2 Jelly Bean Firmware
Step 1: Extract CF-Auto-Root and Odin 3.07 files using winrar/7zip/winzip or any other extracting tool.
Step 2: Switch off the Galaxy S4 I9505. Then boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 3: Launch Odin on the computer.
Step 4: Connect the Galaxy S4 I9505 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn blue with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.
Step 5: In Odin, click the PDA button and select the CF-Auto-Root-jflte-jfltexx-gti9505.tar.md5 file.
Step 6: Verify that Auto Reboot and F.Reset Time checkboxes are selected in Odin. Also, ensure the Re-Partition option in Odin is not selected.
Step 7: Double-check and click Start in Odin. The installation process will now begin.
Step 8: Once the installation process is completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy S4 I9505 running on Android 4.2.2 XXUBMF8 Jelly Bean firmware is now rooted successfully. You can now install any app that requires root permission. Verify the root status of the device by downloading Root Checker app from Google Play Store.

Thank's to all fellas at XDA who first tried out this rooting technique. This method was originally posted via XDA-Developers original thread.

Click here to know How to Update Galaxy S4 I9505 with official Android 4.2.2 XXUBMF8 Jelly Bean firmware.

Thanks for Read How to Root Galaxy S4 I9505 on Android 4.2.2 XXUBMF8 Jelly Bean Firmware Article

How to Update Galaxy Note 10.1 N8000 with Android 4.1.2 XXCMF1 Jelly Bean Official Firmware

Are You Looking For How to Update Galaxy Note 10.1 N8000 with Android 4.1.2 XXCMF1 Jelly Bean Official Firmware

Samsung has released its latest Android 4.1.2 Jelly Bean update with base firmware XXCMF1 for the international 3G + Wi-Fi version of the Galaxy Note 10.1 bearing model number GT-N8000. This update is currently available for the Galaxy Note 10.1 users in most European countries.

Firmware details
PDA: N8000XXCMF1
CSC: N8000OXXCMF1
MODEM: N8000XXCLL1
Version: Android 4.1.2
Built date: Jun 4, 2013
Regions: Slovakia, Macedonia, France, Croatia, Serbia, Greece, Romania, Bulgaria, Spain, Hungary, Finland, Baltic, and Nordic countries.

The new official firmware is currently available as an Over-The-Air (OTA) update as well as through Samsung KIES. However, those who missed the OTA update notification or unable to access the update over Samsung KIES can download and install the same manually, using our step-by-step guide.

Pre-requisites
1. Install USB Driver for Samsung Galaxy Note 10.1 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. Ensure the battery of the phone is charged more than 80 per cent.
5. The Android 4.1.2 XXCMF1 Jelly Bean firmware is compatible only with Samsung Galaxy Note 10.1 N8000. Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy Note 10.1 by navigating to Settings >> About Phone.

File Required
1. Android 4.1.2 XXCMF1 Jelly Bean Firmware for Galaxy Note 10.1 N8000
2. Odin 3.07

Steps to Update Galaxy Note 10.1 N8000 with Android 4.1.2 XXCMF1 Jelly Bean Firmware
Step 1: Extract Firmware zip file that you downloaded already from above link using winrar/7zip/winzip or any other extracting tool, you will get a .tar.md5 file and some other files.
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Power off your phone. Wait 5-6 seconds for vibration to confirm complete switch off.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down and Power buttons together until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the  Galaxy Note 10.1 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.
Step 7: Choose the following files in Odin from extracted N8000XXCMF1 firmware folder by using respective checkboxes:

• Select the PDA checkbox, and choose the file named .tar or .md5.
• Click the Phone checkbox, and choose the file with 'modem' in its name (ignore if there is no such file)
• Click the CSC checkbox, and select the file with 'csc' in its name (ignore if such file is missing)
• Choose the PIT checkbox, and choose the .pit file. Use only the file obtained during extracting in step 1 above, otherwise ignore it.

Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the START button to begin the installation process.
Step 10: Once the installation process is completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy Note 10.1 N8000 should be now updated with official Android 4.1.2 XXCMF1 Jelly Bean firmware. Head over to Settings >> About Phone to verify the software version running on the device.

Note: If Galaxy Note 10.1 N8000 stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.

Click here to know How to Root Galaxy Note 10.1 N8000 running on Android 4.1.2 XXCMF1 Jelly Bean firmware.

Thanks for Read How to Update Galaxy Note 10.1 N8000 with Android 4.1.2 XXCMF1 Jelly Bean Official Firmware Article

How to Root Galaxy Note 10.1 N8000 on Android 4.1.2 XXCMF1 Jelly Bean Firmware

Are You Looking For How to Root Galaxy Note 10.1 N8000 on Android 4.1.2 XXCMF1 Jelly Bean Firmware

Samsung has delivered a new software update based on Android 4.1.2 Jelly Bean with build number N8000XXCMF1 for the European owners of Samsung Galaxy Note 10.1 model number GT-N8000.

Samsung Galaxy Note 10.1 N8000 users who have already updated their devices with Android 4.1.2 XXCMF1 Jelly Bean, may root their devices using the tutorial below.

This tutorial uses CF-Auto-Root file released by recognised XDA Developers, Chainfire. The CF-Auto-Root file allowing Galaxy Note 10.1 users to root their devices easily without depending on the firmware. It completely supports Android 4.1.2 Jelly Bean and future firmware as well. Head over to the CF-Auto-Root main thread to learn more about the root method.

Note: Using this root increases your flash counter. The flash counter keeps track of how many custom firmwares you have flashed, as this voids warranty. Triangle Away can be used to reset the flash counter after installing CF-Auto-Root.

Disclaimer: Rooting voids the warranty of your device. We and the developer of this rooting procedures shall not be held responsible if any undesirable outcomes may happen to your device. use of this root guide is solely at your own risk!

Pre-requisites
1. Install USB Driver for Samsung Galaxy Note 10.1 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy Note 10.1 should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 per cent.
6. The CF-Auto-Root file works only on Samsung Galaxy Note 10.1 N8000. Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy Note 10.1 by navigating to Settings >> About Phone.

File Required
1. CF-Auto-Root for Galaxy Note 10.1 N8000 (CF-Auto-Root-p4noterf-p4noterfxx-gtn8000.zip)
2. Odin 3.07

Steps to Root Galaxy Note 10.1 N8000 Running on Android 4.1.2 Jelly Bean Firmware
Step 1: Extract CF-Auto-Root and Odin 3.07 files using winrar/7zip/winzip or any other extracting tool.
Step 2: Switch off the Galaxy Note 10.1. Then boot the device into Download Mode by pressing and holding Volume Down + Power buttons together until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 3: Launch Odin on the computer.
Step 4: Connect the Galaxy Note 10.1 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.
Step 5: In Odin, click the PDA button and select the CF-Auto-Root-p4noterf-p4noterfxx-gtn8000.tar.md5 file.
Step 6: Verify that Auto Reboot and F.Reset Time checkboxes are selected in Odin. Also, ensure the Re-Partition option in Odin is not selected.
Step 7: Double-check and click Start in Odin. The installation process will now begin.
Step 8: Once the installation process is completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy Note 10.1 N8000 running on Android 4.1.2 Jelly Bean firmware is now rooted successfully. You can now install any app that requires root permission. Verify the root status of the device by downloading Root Checker app from Google Play Store.

Thank's to all fellas at XDA who first tried out this rooting technique. This method was originally posted via XDA-Developer original thread.

Click here to know How to Update Galaxy Note 10.1 N8000 with official Android 4.1.2 XXCMF1 Jelly Bean firmware.

Thanks for Read How to Root Galaxy Note 10.1 N8000 on Android 4.1.2 XXCMF1 Jelly Bean Firmware Article

How to Install ClockworkMod Recovery (CWM) on Galaxy S4 I9505

Are You Looking For How to Install ClockworkMod Recovery (CWM) on Galaxy S4 I9505

ClockworkMod Recovery (CWM) is a replacement recovery option for Android devices, made by Koushik "Koush" Dutta. It is based on the Android 2.1 (Eclair) recovery image. ClockworkMod Recovery allowing users to perform several advanced recovery, restoration, installation and maintenance operations on your Android device that aren't possible with the stock recovery, and is one of the most common ways used to gain root access, back up device data, install custom ROMs, kernels, themes & mods, and more.

Samsung Galaxy S4 I9505 users can now install ClockworkMod Recovery on their devices using the tutorial below.

Pre-requisites
1. Install USB Driver for Samsung Galaxy S4 I9505 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy S4 I9505 should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 per cent.
6. The ClockworkMod Recovery file works only on Samsung Galaxy S4 I9505. Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy S4 I9505 by navigating to Settings >> About Phone.

File Required
1. ClockworkMod Recovery for Galaxy S4 I9505 (i9505-cwm-recovery-6.0.3.2(0611).tar)
2. Odin 3.07

Steps to Install ClockworkMod Recovery on Galaxy S4 I9505
Step 1: Extract Odin 3.07 file using winrar/7zip/winzip or any other extracting tool.
Step 2: Switch off the Galaxy S4 I9505. Then boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 3: Launch Odin on the computer.
Step 4: Connect the Galaxy S4 I9505 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn blue with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.
Step 5: In Odin, click the PDA button and select the i9505-cwm-recovery-6.0.3.2(0611).tar file.
Step 6: Verify that Auto Reboot and F.Reset Time checkboxes are selected in Odin. Also, ensure the Re-Partition option in Odin is not selected.
Step 7: Double-check and click Start in Odin. The installation process will now begin.
Step 8: Once the installation process is completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

That's it, ClockworkMod Recovery is now installed on your Samsung Galaxy S4 I9505.

ClockworkMod Recovery

This method was originally posted via XDA-Developer original thread.

Thanks for Read How to Install ClockworkMod Recovery (CWM) on Galaxy S4 I9505 Article

How to Install TWRP Recovery on Galaxy S4 I9505

Are You Looking For How to Install TWRP Recovery on Galaxy S4 I9505

Team Win Recovery Project (TWRP) is a custom recovery built with ease of use and customization in mind. It's a fully touch driven user interface - no more volume rocker or power buttons to mash. The GUI is also fully XML driven and completely theme-able. You can change just about every aspect of the look and feel.

Key Features
- Ability to save custom recovery settings
- Touchscreen driven with real buttons and drag-to-scroll
- XML-based GUI that allows full customization of the layout – true theming!
- Settings are saved to the sdcard and persist through reboots
- Ability to choose which partitions to back up and which to restore
- Ability to choose to compress backups – now with pigz (multi-core processor support for faster compression times.

Samsung Galaxy S4 I9505 users can now install TWRP on their devices using the tutorial below.

Pre-requisites
1. Install USB Driver for Samsung Galaxy S4 I9505 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy S4 I9505 should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the tablet is charged more than 80 per cent.
6. The TWRP Recovery file works only on Samsung Galaxy S4 I9505. Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy S4 I9505 by navigating to Settings >> About Phone.

File Required
1. TWRP 2.5 for Galaxy S4 I9505 (openrecovery-twrp-2.5.0.2-jfltexx.tar)
2. Odin 3.07

Steps to Install TWRP Recovery on Galaxy S4 I9505
Step 1: Extract Odin 3.07 file using winrar/7zip/winzip or any other extracting tool.
Step 2: Switch off the Galaxy S4 I9505. Then boot the device into Download Mode by pressing and holding Volume Down and Power buttons together until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 3: Launch Odin on the computer.
Step 4: Connect the Galaxy S4 I9505 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn blue with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.
Step 5: In Odin, click the PDA button and select the openrecovery-twrp-2.5.0.2-jfltexx.tar file.
Step 6: Verify that Auto Reboot and F.Reset Time checkboxes are selected in Odin. Also, ensure the Re-Partition option in Odin is not selected.
Step 7: Double-check and click Start in Odin. The installation process will now begin.
Step 8: Once the installation process is completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

That's it, TWRP recovery is now installed on your Samsung Galaxy S4 I9505.

TWRP Recovery

This method was originally posted via XDA-Developer original thread.

Thanks for Read How to Install TWRP Recovery on Galaxy S4 I9505 Article

How to Update Galaxy S4 I9505 with Leaked Android 4.3 Jelly Bean Firmware

Are You Looking For How to Update Galaxy S4 I9505 with Leaked Android 4.3 Jelly Bean Firmware

Owners of Samsung Galaxy S4 with model number GT-I9505 can now try out the features and capabilities of Android 4.3 Jelly Bean. SamMobile has reportedly managed to port the leaked Android 4.3 from Galaxy S4 Google Play Edition (GT-I9505G) to the Snapdragon variant of Samsung Galaxy S4.

System details
PDA: I9505GUEUBMFP
CSC: I9505GXARBMFP
Version: Android 4.3
Built date: Jun 26, 2013

Samsung Galaxy S4 I9505 users can now install the leaked Android 4.3 Jelly Bean on their devices by following the tutorial below.

Pre-requisites
1. Install USB Driver for Samsung Galaxy S4 I9505 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy S4 I9505 should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 per cent.
6. Root Galaxy S4 I9505
7. Install Custom Recovery (CWM or TWRP).
8. The leaked Android 4.3 Jelly Bean firmware is compatible only with Samsung Galaxy S4 I9505. Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy S4 I9505 by navigating to Settings >> About Phone.

File Required
Leaked Android 4.3 Jelly Bean Firmware (Choose either one)
- Android-4.3-I9505GUEUBMFP-Odexed-I9505.zip
MD5: 363ED9CC32A841A512E72372A19C7D05
- Android-4.3-I9505GUEUBMFP-Deodexed-I9505.zip
MD5: 74D241B64266220161018EB98A19F279

Steps to Update Galaxy S4 I9505 with Leaked Android 4.3 Jelly Bean Firmware
Step 1: Connect the Galaxy S4 I9505 to the computer using USB cable.
Step 2: Copy the Leaked Android 4.3 Jelly Bean Firmware file to internal SD card of your phone.
Step 3: Once the file transfer process is completed, switch off the phone and disconnect it from computer.
Step 4: Boot the device into CWM Recovery by pressing and holding Volume Up, Home, and Power buttons together until the device turns on.
Step 5 (optional): In CWM Recovery mode, create a Nandroid backup of your currently installed ROM by navigating to Backup and Restore >> Backup. Once backup process is completed, return to main recovery menu.
Step 6: Perform a Wipe data/Factory Reset (Necessary due to new Android version).
Step 7: Select install zip from sdcard and then choose zip from sdcard. Now, navigate to the Leaked Android 4.3 Jelly Bean Firmware file that you copied earlier and confirm the installation.

Step 8: Once installation process is completed, return to main recovery menu and select Reboot System Now.

Samsung Galaxy S4 I9505 should be now running on the leaked Android 4.3 Jelly Bean firmware. Head over to Settings >> About Phone to verify the software version running on the device.

Source: SamMobile

Thanks for Read How to Update Galaxy S4 I9505 with Leaked Android 4.3 Jelly Bean Firmware Article

How to Update Galaxy S4 (U.S. Cellular) SCH-R970 with Android 4.2.2 VXUAMF5 Jelly Bean Official Firmware

Are You Looking For How to Update Galaxy S4 (U.S. Cellular) SCH-R970 with Android 4.2.2 VXUAMF5 Jelly Bean Official Firmware

Samsung recently released its latest Android 4.2.2 Jelly Bean update with base firmware VXUAMF5 for the U.S. Cellular subscribers of Galaxy S4 (SCH-R970).

Firmware details
PDA: R970VXUAMF5
CSC: R970USCAMF5
MODEM: R970VXUAMF5
Version: Android 4.2.2
Built date: Jun 19, 2013
Regions: USA (U.S. Cellular)

The new official firmware is currently available as an Over-The-Air (OTA) update as well as through Samsung KIES. However, those who missed the OTA update notification or unable to access the update over Samsung KIES can download and install the same manually, using our step-by-step guide.

Pre-requisites
1. Install USB Driver for Samsung Galaxy S4 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. Ensure the battery of the phone is charged more than 80 per cent.
5. The Android 4.2.2 VXUAMF5 Jelly Bean firmware is compatible only with Samsung Galaxy S4 (U.S. Cellular) SCH-R970. Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy S4 by navigating to Settings >> About Phone.

File Required
1. Android 4.2.2 VXUAMF5 Jelly Bean Firmware for Galaxy S4 (U.S. Cellular) SCH-R970
2. Odin 3.07

Steps to Update Galaxy S4 (U.S. Cellular) SCH-R970 with Android 4.2.2 VXUAMF5 Jelly Bean Firmware
Step 1: Extract Firmware zip file that you downloaded already from above link using winrar/7zip/winzip or any other extracting tool, you will get a .tar.md5 file and some other files.
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Power off your phone. Wait 5-6 seconds for vibration to confirm complete switch off.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy S4 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn blue with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.
Step 7: Choose the following files in Odin from extracted R970VXUAMF5 firmware folder by using respective checkboxes:

• Select the PDA checkbox, and choose the file named .tar or .md5.
• Click the Phone checkbox, and choose the file with 'modem' in its name (ignore if there is no such file)
• Click the CSC checkbox, and select the file with 'csc' in its name (ignore if such file is missing)
• Choose the PIT checkbox, and choose the .pit file. Use only the file obtained during extracting in step 1 above, otherwise ignore it.

Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the START button to begin the installation process.
Step 10: Once the installation process is completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy S4 (U.S. Cellular) SCH-R970 should be now updated with official Android 4.2.2 VXUAMF5 Jelly Bean. Head over to Settings >> About Phone to verify the software version running on the device.

Note: If Galaxy S4 (U.S. Cellular) SCH-R970 stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up, Home and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.

Click here to know How to Root Galaxy S4 (U.S. Cellular) SCH-R970 running on Android 4.2.2 VXUAMF5 Jelly Bean firmware.

Thanks for Read How to Update Galaxy S4 (U.S. Cellular) SCH-R970 with Android 4.2.2 VXUAMF5 Jelly Bean Official Firmware Article

How to Root Galaxy S4 (U.S. Cellular) SCH-R970 on Android 4.2.2 VXUAMF5 Jelly Bean Firmware

Are You Looking For How to Root Galaxy S4 (U.S. Cellular) SCH-R970 on Android 4.2.2 VXUAMF5 Jelly Bean Firmware

Samsung has rolled out Android 4.2.2 Jelly Bean firmware update for the U.S. Cellular subscribers of Galaxy S4 bearing model number SCH-R970. The new official firmware is now available as an Over-The-Air (OTA) update as well as through Samsung KIES.

Samsung Galaxy S4 (U.S. Cellular) SCH-R970 users who have already updated their devices with Android 4.2.2 VXUAMF5 Jelly Bean, may root their devices using the tutorial below.

This tutorial uses CF-Auto-Root file released by recognised XDA Developers, Chainfire. The CF-Auto-Root file allowing Galaxy S4 (U.S. Cellular) users to root their devices easily without depending on the firmware. It completely supports Android 4.2.2 Jelly Bean and future firmware as well. Head over to the CF-Auto-Root main thread to learn more about the root method.

Note: Using this root increases your flash counter. The flash counter keeps track of how many custom firmwares you have flashed, as this voids warranty. Triangle Away can be used to reset the flash counter after installing CF-Auto-Root.

Disclaimer: Rooting voids the warranty of your device. We and the developer of this rooting procedures shall not be held responsible if any undesirable outcomes may happen to your device. use of this root guide is solely at your own risk!

Pre-requisites
1. Install USB Driver for Samsung Galaxy S4 the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. Ensure the battery of the phone is charged more than 80 per cent.
5. The CF-Auto-Root file works only on Samsung Galaxy S4 (U.S. Cellular) SCH-R970. Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy S4 by navigating to Settings >> About Phone.

File Required
1. CF-Auto-Root for Galaxy S4 (U.S. Cellular) SCH-R970 (CF-Auto-Root-jflteusc-jflteusc-schr970.zip)
2. Odin 3.07

Steps to Root Galaxy S4 (U.S. Cellular) SCH-R970 Running on Android 4.2.2 VXUAMF5 Jelly Bean Firmware
Step 1: Extract CF-Auto-Root and Odin 3.07 files using winrar/7zip/winzip or any other extracting tool.
Step 2: Switch off the Galaxy S4. Then boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 3: Launch Odin on the computer.
Step 4: Connect the Galaxy S4 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.
Step 5: In Odin, click the PDA button and select the CF-Auto-Root-jflteusc-jflteusc-schr970.tar.md5 file.
Step 6: Verify that Auto Reboot and F.Reset Time checkboxes are selected in Odin. Also, ensure the Re-Partition option in Odin is not selected.
Step 7: Double-check and click Start in Odin. The installation process will now begin.
Step 8: Once the installation process is completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy S4 (U.S. Cellular) SCH-R970 running on Android 4.2.2 VXUAMF5 Jelly Bean firmware is now rooted successfully. You can now install any app that requires root permission. Verify the root status of the device by downloading Root Checker app from Google Play Store.

Click here to know How to Update Galaxy S4 (U.S. Cellular) SCH-R970 with Android 4.2.2 VXUAMF5 Jelly Bean official firmware.

Thanks for Read How to Root Galaxy S4 (U.S. Cellular) SCH-R970 on Android 4.2.2 VXUAMF5 Jelly Bean Firmware Article

How to Update Galaxy S4 I9500 with Android 4.2.2 XXUBMF8 Jelly Bean Official Firmware

Are You Looking For How to Update Galaxy S4 I9500 with Android 4.2.2 XXUBMF8 Jelly Bean Official Firmware

Southeast Asian owners of Samsung Galaxy S4 Exynos variant (GT-I9500) have received a new software update based on Android 4.2.2 Jelly Bean with firmware build number I9500XXUBMF8. The new official firmware is currently hitting Vietnam and Thailand as an Over-The-Air (OTA) update as well as through Samsung KIES.

Firmware details
PDA: I9500XXUBMF8
CSC: I9500OLBBMF8
MODEM: I9500DXUBMF8
Version: Android 4.2.2
Built date: Jun 19, 2013
Regions: Indonesia, Malaysia, Philippines, Singapore, Vietnam, Thailand

Samsung Galaxy S4 I9500 users who missed the OTA update notification or unable to access the update over Samsung KIES, may follow our step-by-step guide to install the update manually.

Pre-requisites
1. Install USB Driver for Samsung Galaxy S4 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy S4 should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 per cent.
6. The Android 4.2.2 XXUBMF8 Jelly Bean firmware is compatible only with Samsung Galaxy S4 I9500. Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy S4 by navigating to Settings >> About Phone.

File Required
1. Android 4.2.2 XXUBMF8 Jelly Bean Firmware for Samsung Galaxy S4 I9500
2. Odin 3.07

Steps to Update Galaxy S4 I9500 with Android 4.2.2 XXUBMF8 Jelly Bean Firmware
Step 1: Extract Firmware zip file that you downloaded already from above link using winrar/7zip/winzip or any other extracting tool, you will get a .tar.md5 file and some other files.
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Power off your phone. Wait 5-6 seconds for vibration to confirm complete switch off.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy S4 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn blue with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.
Step 7: Choose the following files in Odin from extracted I9505XXUBMF8 firmware folder by using respective checkboxes:

• Select the PDA checkbox, and choose the file named .tar or .md5.
• Click the Phone checkbox, and choose the file with 'modem' in its name (ignore if there is no such file)
• Click the CSC checkbox, and select the file with 'csc' in its name (ignore if such file is missing)
• Choose the PIT checkbox, and choose the .pit file. Use only the file obtained during extracting in step 1 above, otherwise ignore it.

Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the START button to begin the installation process.
Step 10: Once the installation process is completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy S4 I9500 should be now updated with official Android 4.2.2 XXUBMF8 Jelly Bean. Head over to Settings >> About Phone to verify the software version running on the device.

Note: If Galaxy S4 I9500 stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up, Home and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.

Click here to know How to Root Galaxy S4 I9500 running on Android 4.2.2 XXUBMF8 Jelly Bean firmware.

Thanks for Read How to Update Galaxy S4 I9500 with Android 4.2.2 XXUBMF8 Jelly Bean Official Firmware Article

How to Root Galaxy S4 I9500 on Android 4.2.2 XXUBMF8 Jelly Bean Firmware

Are You Looking For How to Root Galaxy S4 I9500 on Android 4.2.2 XXUBMF8 Jelly Bean Firmware

Samsung recently released another official Android 4.2.2 Jelly Bean update with firmware build number I9500XXUBMF8 on the Exynos 5 octa-core variant of Samsung Galaxy S4 (GT-I9500).

Samsung Galaxy S4 I9500 users who have already updated their devices with Android 4.2.2 XXUBMF8 Jelly Bean, may root their devices using the tutorial below.

This tutorial uses CF-Auto-Root file released by recognised XDA Developers, Chainfire. The CF-Auto-Root file allowing Galaxy S4 users to root their devices easily without depending on the firmware. It completely supports Android 4.2.2 Jelly Bean and future firmware as well. Head over to the CF-Auto-Root main thread to learn more about the root method.

Disclaimer: Rooting voids the warranty of your device. We and the developer of this rooting procedures shall not be held responsible if any undesirable outcomes may happen to your device. use of this root guide is solely at your own risk!

Pre-requisites
1. Install USB Driver for Samsung Galaxy S4 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy S4 should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 per cent.
6. The CF-Auto-Root file works only on Samsung Galaxy S4 I9500. Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy S4 by navigating to Settings >> About Phone.

File Required
1. CF-Auto-Root for Galaxy S4 I9500 (CF-Auto-Root-ja3g-ja3gxx-gti9500.zip)
2. Odin 3.07

Steps to Root Galaxy S4 I9500 Running on Android 4.2.2 Jelly Bean Firmware
Step 1: Extract CF-Auto-Root and Odin 3.07 files using winrar/7zip/winzip or any other extracting tool.
Step 2: Switch off the Galaxy S4. Then boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 3: Launch Odin on the computer.
Step 4: Connect the Galaxy S4 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn blue with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.
Step 5: In Odin, click the PDA button and select the CF-Auto-Root-ja3g-ja3gxx-gti9500.tar.md5 file.
Step 6: Verify that Auto Reboot and F.Reset Time checkboxes are selected in Odin. Also, ensure the Re-Partition option in Odin is not selected.
Step 7: Double-check and click Start in Odin. The installation process will now begin.
Step 8: Once the installation process is completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy S4 I9500 running on Android 4.2.2 XXUBMF8 Jelly Bean firmware is now rooted successfully. You can now install any app that requires root permission. Verify the root status of the device by downloading Root Checker app from Google Play Store.

Thank's to all fellas at XDA who first tried out this rooting technique. This method was originally posted via XDA-Developers original thread.

Click here to know How to Update Galaxy S4 I9500 with official Android 4.2.2 XXUBMF8 Jelly Bean firmware.

Thanks for Read How to Root Galaxy S4 I9500 on Android 4.2.2 XXUBMF8 Jelly Bean Firmware Article

How to Update Galaxy S3 (Verizon) SCH-I535 with Android 4.1.2 VRBMF1 Jelly Bean Official Firmware

Are You Looking For How to Update Galaxy S3 (Verizon) SCH-I535 with Android 4.1.2 VRBMF1 Jelly Bean Official Firmware

Another Android 4.1.2 Jelly Bean update with base firmware VRBMF1 has been rolled out on Verizon version of Samsung Galaxy S3 with model number SCH-I535. The new official firmware is currently available as an Over-The-Air (OTA) update as well as through Samsung KIES.

Firmware details
PDA: I535VRBMF1
CSC: I535VZWBMF1
MODEM: I535VRBMF1
Version: Android 4.1.2
Built date: Jun 8, 2013
Regions: USA (Verizon)

Samsung Galaxy S3 (Verizon) SCH-I535 users who missed the OTA update notification or unable to access the update over Samsung KIES, may follow our step-by-step guide to install the update manually.

Pre-requisites
1. Install USB Driver for Samsung Galaxy S3 (Verizon) on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. Ensure the battery of the phone is charged more than 80 per cent.
5. The Android 4.1.2 VRBMF1 Jelly Bean firmware is compatible only with Galaxy S3 (Verizon) SCH-I535. Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy S3 by navigating to Settings >> About Phone.

File Required
1. Android 4.1.2 VRBMF1 Jelly Bean Firmware for Galaxy S3 (Verizon) SCH-I535
2. Odin 3.07

Steps to Update Galaxy S3 (Verizon) SCH-I535 with Android 4.1.2 VRBMF1 Jelly Bean Firmware
Step 1: Extract Firmware zip file that you downloaded already from above link using winrar/7zip/winzip or any other extracting tool, you will get a .tar.md5 file and some other files.
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Power off your phone. Wait 5-6 seconds for vibration to confirm complete switch off.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy S3 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.
Step 7: Choose the following files in Odin from extracted I535VRBMF1 firmware folder by using respective checkboxes:

• Select the PDA checkbox, and choose the file named .tar or .md5.
• Click the Phone checkbox, and choose the file with 'modem' in its name (ignore if there is no such file)
• Click the CSC checkbox, and select the file with 'csc' in its name (ignore if such file is missing)
• Choose the PIT checkbox, and choose the .pit file. Use only the file obtained during extracting in step 1 above, otherwise ignore it.

Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the START button to begin the installation process.
Step 10: Once the installation process is completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy S3 (Verizon) SCH-I535 should be now updated with official Android 4.1.2 VRBMF1 Jelly Bean firmware. Head over to Settings >> About Phone to verify the software version running on the device.

Note: If Galaxy S3 (Verizon) SCH-I535 stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up, Home and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.

Thanks for Read How to Update Galaxy S3 (Verizon) SCH-I535 with Android 4.1.2 VRBMF1 Jelly Bean Official Firmware Article

How to Update Galaxy S4 I9500 with Android 4.2.2 XWUBMG1 Jelly Bean Official Firmware

Are You Looking For How to Update Galaxy S4 I9500 with Android 4.2.2 XWUBMG1 Jelly Bean Official Firmware

Samsung recently started rolling out another official Android 4.2.2 Jelly Bean update with base firmware XWUBMG1 for the Exynos 5 octa-core variant of Galaxy S4 bearing model number GT-I9500. The new official firmware is now available for download through Samsung KIES as well as Over-The-Air (OTA) update.

Firmware details
PDA: I9500XWUBMG1
CSC: I9500ODDBMG1
MODEM: I9500DDUBMF8
Version: Android 4.2.2
Built date: Jul 2, 2013
Regions: India, Nepal, Sri Lanka, Bangladesh

Samsung Galaxy S4 I9500 users who missed the OTA update notification or unable to access the update over Samsung KIES, may follow our step-by-step guide to install the update manually.

Pre-requisites
1. Install USB Driver for Samsung Galaxy S4 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy S4 should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 per cent.
6. The Android 4.2.2 XWUBMG1 Jelly Bean firmware is compatible only with Samsung Galaxy S4 I9500. Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy S4 by navigating to Settings >> About Phone.

File Required
1. Android 4.2.2 XWUBMG1 Jelly Bean Firmware for Samsung Galaxy S4 I9500
2. Odin 3.07

Steps to Update Galaxy S4 I9500 with Android 4.2.2 XWUBMG1 Jelly Bean Firmware
Step 1: Extract Firmware zip file that you downloaded already from above link using winrar/7zip/winzip or any other extracting tool, you will get a .tar.md5 file and some other files.
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Power off your phone. Wait 5-6 seconds for vibration to confirm complete switch off.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy S4 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn blue with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.
Step 7: Choose the following files in Odin from extracted I9500XWUBMG1 firmware folder by using respective checkboxes:

• Select the PDA checkbox, and choose the file named .tar or .md5.
• Click the Phone checkbox, and choose the file with 'modem' in its name (ignore if there is no such file)
• Click the CSC checkbox, and select the file with 'csc' in its name (ignore if such file is missing)
• Choose the PIT checkbox, and choose the .pit file. Use only the file obtained during extracting in step 1 above, otherwise ignore it.

Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the START button to begin the installation process.
Step 10: Once the installation process is completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy S4 I9500 should be now updated with official Android 4.2.2 XWUBMG1 Jelly Bean. Head over to Settings >> About Phone to verify the software version running on the device.

Note: If Galaxy S4 I9500 stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up, Home and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.

Click here to know How to Root Galaxy S4 I9500 running on Android 4.2.2 XWUBMG1 Jelly Bean firmware.

Thanks for Read How to Update Galaxy S4 I9500 with Android 4.2.2 XWUBMG1 Jelly Bean Official Firmware Article