How to Update Galaxy Note 2 N7100 with Android 4.1.2 XXDME1 Jelly Bean Official Firmware

Are You Looking For How to Update Galaxy Note 2 N7100 with Android 4.1.2 XXDME1 Jelly Bean Official Firmware

Samsung recently rolled out its latest official Jelly Bean update, Android 4.1.2 with base firmware XXDME1, for Galaxy Note 2 GT-N7100 users in Southeast Asia countries - Indonesia, Malaysia, Philippines, Singapore,Vietnam and Thailand.

Firmware details
PDA: N7100XXDME1
CSC: N7100OLBDMD2
Version: Android 4.1.2
Built date: May, 2013
Regions: Indonesia, Malaysia, Philippines, Singapore, Vietnam, Thailand

The official firmware is now available for download via Over-The-Air (OTA) update as well as through Samsung KIES. However, those who fail to upgrade their devices using official method, may follow our step-by-step guide to install the update manually.

Pre-requisites
1. Install USB Driver for Samsung Galaxy Note on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy Note 2 should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 per cent.
6. The Android 4.1.2 XXDME1 Jelly Bean firmware is compatible only with Samsung Galaxy Note 2 N7100. Installing this on any incorrect variant will brick the device. Verify the model number of the Galaxy Note 2 by navigating to Settings >> About Phone.

File Required
1. Android 4.1.2 XXDME1 Jelly Bean Firmware
2. Odin 3.07

Steps to Update Galaxy Note 2 N7100 with Android 4.1.2 XXDME1 Jelly Bean Firmware
Step 1: Extract Firmware zip file that you downloaded already from above link, you will get a .tar.md5 file and some other files.
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Power off your phone. Wait 5-6 seconds for vibration to confirm complete switch off.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy Note 2 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added. If Odin fails to detect the device then re-install USB driver.
Step 7: Choose the following files in Odin from extracted N7100XXDME1 firmware folder by using respective checkboxes:

• Select the PDA checkbox, and choose the file named .tar or .md5.
• Click the Phone checkbox, and choose the file with 'modem' in its name (ignore if there is no such file)
• Click the CSC checkbox, and select the file with 'csc' in its name (ignore if such file is missing)
• Choose the PIT checkbox, and choose the .pit file. Use only the file obtained during extracting in step 1 above, otherwise ignore it.

Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the START button to begin the flashing process.
Step 10: Once flashing completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy Note 2 N7100 should be now updated with official Android 4.1.2 XXDME1 Jelly Bean. Head over to Settings >> About Phone to verify the software version running on the device.

Note: If Galaxy Note 2 N7100 stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up, Home and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.

Click here to know How to Root Galaxy Note 2 N7100 running on Android 4.1.2 XXDME1 Jelly Bean firmware.

Thanks for Read How to Update Galaxy Note 2 N7100 with Android 4.1.2 XXDME1 Jelly Bean Official Firmware Article

How to Root Galaxy Note 2 N7100 on Android 4.1.2 XXDME1 Jelly Bean Firmware

Are You Looking For How to Root Galaxy Note 2 N7100 on Android 4.1.2 XXDME1 Jelly Bean Firmware

Samsung Galaxy Note 2 N7100 users who have already updated their devices with Android 4.1.2 XXDME1 Jelly Bean firmware, may root their devices using the tutorial below.

This tutorial uses CF-Auto-Root file released by recognised XDA Developers, Chainfire. The CF-Auto-Root file allowing Galaxy Note 2 users to root their devices easily without depending on the firmware. It completely supports Android 4.1.2 Jelly Bean and future firmware as well.

Disclaimer: Rooting voids the warranty of your device. We and the developer of this rooting procedures shall not be held responsible if any undesirable outcomes may happen to your device. use of this root guide is solely at your own risk!

Pre-requisites
1. Install USB Driver for Samsung Galaxy Note on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy Note 2 should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 per cent.
6. The CF-Auto-Root file works only on Samsung Galaxy Note 2 N7100. Applying this on any incorrect variant will brick the device. Verify the model number of the Galaxy Note 2 by navigating to Settings >> About Phone.

File Required
1. CF-Auto-Root for Galaxy Note 2 N7100  (CF-Auto-Root-t03g-t03gxx-gtn7100.zip)
2. Odin 3.07

Steps to Root Galaxy Note 2 N7100 on Android 4.1.2 XXDME1 Jelly Bean Firmware
Step 1: Extract downloaded CF-Auto-Root zip file and you will find a .tar.md5 file within it.
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Power off your phone. Wait 5-6 seconds for vibration to confirm complete switch off.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy Note 2 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added. If Odin fails to detect the device then re-install USB driver.
Step 7: Select these files in Odin at respective buttons:

• Click the PDA Button, and select CF-Auto-Root-t03g-t03gxx-gtn7100.tar.md5.

Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the START button to begin the flashing process.
Step 10: Once flashing completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Your Samsung Galaxy Note 2 N7100 running on Android 4.1.2 XXDME1 Jelly Bean firmware is now rooted successfully. You may now install any app that requires root permission.

Thank's to all fellas at XDA who first tried out this rooting technique. This root method was originally posted via XDA-Developer original thread.

Thanks for Read How to Root Galaxy Note 2 N7100 on Android 4.1.2 XXDME1 Jelly Bean Firmware Article

How to Update Galaxy Note 8.0 N5100 with Android 4.1.2 XXBMD1 Jelly Bean Official Firmware

Are You Looking For How to Update Galaxy Note 8.0 N5100 with Android 4.1.2 XXBMD1 Jelly Bean Official Firmware

Samsung recently released its latest official Android 4.1.2 Jelly Bean update with base firmware XXBMD1 for the international version of Galaxy Note 8.0 bearing model number GT-N5100.

Firmware details
PDA: N5100XXBMD1
CSC: N5100OLBBMC8
Version: Android 4.1.2
Built date: April, 2013
Regions: Indonesia, Malaysia, Philippines, Singapore, Vietnam, Thailand

The official firmware is now available for download via Over-The-Air (OTA) update as well as through Samsung KIES. However, those who fail to upgrade their devices with Android 4.1.2 XXBMD1 Jelly Bean using official method, may follow our step-by-step guide to install the update manually.

Pre-requisites
1. Install USB Driver for Samsung  Galaxy Note 8.0 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The  Galaxy Note 8.0 should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 per cent.
6. The Android 4.1.2 XXBMD1 Jelly Bean firmware is compatible only with Samsung Galaxy Note 8.0 N5100. Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy Note 8.0 by navigating to Settings >> About Phone.

File Required
1. Android 4.1.2 XXBMD1 Jelly Bean Firmware
2. Odin 3.07

Steps to Update Galaxy Note 8.0 N5100 with Android 4.1.2 XXBMD1 Jelly Bean Firmware
Step 1: Extract Firmware zip file that you downloaded already from above link, you will get a .tar.md5 file and some other files.
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Power off your phone. Wait 5-6 seconds for vibration to confirm complete switch off.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the  Galaxy Note 8.0 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added. If Odin fails to detect the device then re-install USB driver.
Step 7: Choose the following files in Odin from extracted N5100XXBMD1 firmware folder by using respective checkboxes:

• Select the PDA checkbox, and choose the file named .tar or .md5.
• Click the Phone checkbox, and choose the file with 'modem' in its name (ignore if there is no such file)
• Click the CSC checkbox, and select the file with 'csc' in its name (ignore if such file is missing)
• Choose the PIT checkbox, and choose the .pit file. Use only the file obtained during extracting in step 1 above, otherwise ignore it.

Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the START button to begin the flashing process.
Step 10: Once flashing completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung  Galaxy Note 8.0 N5100 should be now updated with official Android 4.1.2 XXBMD1 Jelly Bean. Head over to Settings >> About Phone to verify the software version running on the device.

Note: If  Galaxy Note 8.0 N5100 stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up, Home and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.

Screenshot: Already updated!

Click here to know How to Root Galaxy Note 8.0 N5100 running on Android 4.1.2 XXBMD1 Jelly Bean firmware.

Thanks for Read How to Update Galaxy Note 8.0 N5100 with Android 4.1.2 XXBMD1 Jelly Bean Official Firmware Article

How to Root Galaxy Note 8.0 N5100 on Android 4.1.2 XXBMD1 Jelly Bean Firmware

Are You Looking For How to Root Galaxy Note 8.0 N5100 on Android 4.1.2 XXBMD1 Jelly Bean Firmware

An Official Android 4.1.2 Jelly Bean Over-The-Air (OTA) update with base firmware XXBMD1 has been released for the international version of Samsung Galaxy Note 8.0 bearing model number GT-N5100.

Samsung Galaxy Note 8.0 N5100 users who have already updated their devices with Android 4.1.2 XXBMD1 Jelly Bean firmware, may root their devices using the tutorial below.

This tutorial uses CF-Auto-Root file released by recognised XDA Developers, Chainfire. The CF-Auto-Root file allowing Galaxy Note 8.0 users to root their devices easily without depending on the firmware. It completely supports Android 4.1.2 Jelly Bean and future firmware as well.

Disclaimer: Rooting voids the warranty of your device. We and the developer of this rooting procedures shall not be held responsible if any undesirable outcomes may happen to your device. use of this root guide is solely at your own risk!

Pre-requisites
1. Install USB Driver for Samsung Galaxy Note 8.0 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy Note 8.0 should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 per cent.
6. The CF-Auto-Root file works only on Samsung Galaxy Note 8.0 N5100. Applying this on any incorrect variant will brick the device. Verify the model number of the Galaxy Note 8.0 by navigating to Settings >> About Phone.

File Required
1. CF-Auto-Root  for Galaxy Note 8.0 N5100 (CF-Auto-Root-kona3g-kona3gxx-gtn5100.zip)
2. Odin 3.07

Steps to Root Galaxy Note 8.0 N5100 on Android 4.1.2 XXBMD1 Jelly Bean Firmware
Step 1: Extract downloaded CF-Auto-Root zip file and you will find a .tar.md5 file within it.
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Power off your phone. Wait 5-6 seconds for vibration to confirm complete switch off.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy Note 8.0 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added. If Odin fails to detect the device then re-install USB driver.
Step 7: Select these files in Odin at respective buttons:

• Click the PDA Button, and select CF-Auto-Root-kona3g-kona3gxx-gtn5100.tar.md5.

Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the START button to begin the flashing process.
Step 10: Once flashing completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Your Samsung Galaxy Note 8.0 N5100 running on Android 4.1.2 XXBMD1 Jelly Bean firmware is now rooted successfully. You may now install any app that requires root permission.

Note: Tested working on Galaxy Note 8.0 N5100 with Android 4.1.2 XXBMD1 Jelly Bean firmware, should work with other Jelly Bean firmware.

Screenshot 1: Flashing CF-Auto-Root via Odin

Screenshot 2: Rooted!

Thank's to all fellas at XDA who first tried out this rooting technique. This root method was originally posted via XDA-Developers original thread.

Thanks for Read How to Root Galaxy Note 8.0 N5100 on Android 4.1.2 XXBMD1 Jelly Bean Firmware Article

How to Root Galaxy Note 10.1 N8000 on Android 4.1.2 Jelly Bean Firmware

Are You Looking For How to Root Galaxy Note 10.1 N8000 on Android 4.1.2 Jelly Bean Firmware

Samsung Galaxy Note 10.1 N8000 users who have already updated their devices with Android 4.1.2 Jelly Bean, may root their devices using the tutorial below.

This tutorial uses CF-Auto-Root file released by recognised XDA Developers, Chainfire. The CF-Auto-Root file allowing Galaxy Note 10.1 users to root their devices easily without depending on the firmware. It completely supports Android 4.1.2 Jelly Bean and future firmware as well.

Disclaimer: Rooting voids the warranty of your device. We and the developer of this rooting procedures shall not be held responsible if any undesirable outcomes may happen to your device. use of this root guide is solely at your own risk!

Pre-requisites
1. Install USB Driver for Samsung Galaxy Note 10.1 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options (Android 4.0 or later) or go to Settings >> Applications >> Development (Android 2.3 or earlier).
3. Make a backup of all your important data before following the guide.
4. The Galaxy Note 10.1 should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 per cent.
6. The CF-Auto-Root file works only on Samsung Galaxy Note 10.1 N8000. Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy Note 10.1 by navigating to Settings >> About Phone.

File Required
1. CF-Auto-Root for Galaxy Note 10.1 N8000 (CF-Auto-Root-p4noterf-p4noterfxx-gtn8000.zip)
2. Odin 3.07

Steps to Root Galaxy Note 10.1 N8000 Running on Android 4.1.2 Jelly Bean Firmware
Step 1: Extract CF-Auto-Root and Odin 3.07 files using winrar/7zip/winzip or any other extracting tool.
Step 2: Switch off the Galaxy Note 10.1. Then boot the device into Download Mode by pressing and holding Volume Down + Power buttons together until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 3: Launch Odin on the computer.
Step 4: Connect the Galaxy Note 10.1 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added. If Odin fails to detect the device then re-install USB driver.
Step 5: In Odin, click the PDA button and select the CF-Auto-Root-p4noterf-p4noterfxx-gtn8000.tar.md5 file.
Step 6: Verify that Auto Reboot and F.Reset Time checkboxes are selected in Odin. Also, ensure the Re-Partition option in Odin is not selected.
Step 7: Double-check and click Start in Odin. The installation process will now begin.
Step 8: Once flashing completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy Note 10.1 N8000 running on Android 4.1.2 Jelly Bean firmware is now rooted successfully. You can now install any app that requires root permission. Verify the root status of the device by downloading Root Checker app from Google Play Store.

Thank's to all fellas at XDA who first tried out this rooting technique. This method was originally posted via XDA-Developer original thread.

Thanks for Read How to Root Galaxy Note 10.1 N8000 on Android 4.1.2 Jelly Bean Firmware Article

How to Update Galaxy Note 2 (AT&T) SGH-I317 with Android 4.1.2 UCAMA4 Jelly Bean Official Firmware

Are You Looking For How to Update Galaxy Note 2 (AT&T) SGH-I317 with Android 4.1.2 UCAMA4 Jelly Bean Official Firmware

Samsung has released Android 4.1.2 Jelly Bean Over-The-Air (OTA) update with firmware build number I317UCAMA4 for the AT&T subscribers of Galaxy Note 2 bearing model number SGH-I317.

Firmware details
PDA: I317UCAMA4
CSC: I317ATTAMA4
MODEM: I317UCAMA4
Version: Android 4.1.2
Built date: Jan 18, 2013
Regions: USA (AT&T)

Samsung Galaxy Note 2 (AT&T) SGH-I317 users who missed the OTA update notification or unable to access the update over Samsung KIES, may follow our step-by-step guide to install the update manually.

Pre-requisites
1. Install USB Driver for Samsung Galaxy Note 2 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. Ensure the battery of the phone is charged more than 80 per cent.
5. The Android 4.1.2 UCAMA4 Jelly Bean firmware is compatible only with Samsung Galaxy Note 2 (AT&T) SGH-I317. Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy Note 2 by navigating to Settings >> About Phone.

File Required
1. Android 4.1.2 UCAMA4 Jelly Bean Firmware for Galaxy Note 2 (AT&T) SGH-I317
2. Odin 3.07

Steps to Update Galaxy Note 2 (AT&T) SGH-I317 with Android 4.1.2 UCAMA4 Jelly Bean Firmware
Step 1: Extract Firmware zip file that you downloaded already from above link using winrar/7zip/winzip or any other extracting tool, you will get a .tar.md5 file and some other files.
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Power off your phone. Wait 5-6 seconds for vibration to confirm complete switch off.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy Note 2 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.
Step 7: Choose the following files in Odin from extracted I317UCAMA4 firmware folder by using respective checkboxes:

• Select the PDA checkbox, and choose the file named .tar or .md5.
• Click the Phone checkbox, and choose the file with 'modem' in its name (ignore if there is no such file)
• Click the CSC checkbox, and select the file with 'csc' in its name (ignore if such file is missing)
• Choose the PIT checkbox, and choose the .pit file. Use only the file obtained during extracting in step 1 above, otherwise ignore it.

Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the START button to begin the installation process.
Step 10: Once the installation process is completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy Note 2 (AT&T) SGH-I317 should be now updated with official Android 4.1.2 UCAMA4 Jelly Bean firmware. Head over to Settings >> About Phone to verify the software version running on the device.

Note: If Galaxy Note 2 (AT&T) SGH-I317 stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up, Home and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.

Click here to know How to Root Galaxy Note 2 (AT&T) SGH-I317 running on Android 4.1.2 Jelly Bean firmware.

Thanks for Read How to Update Galaxy Note 2 (AT&T) SGH-I317 with Android 4.1.2 UCAMA4 Jelly Bean Official Firmware Article

How to Root Galaxy Note 2 (AT&T) SGH-I317 on Android 4.1.2 Jelly Bean Firmware

Are You Looking For How to Root Galaxy Note 2 (AT&T) SGH-I317 on Android 4.1.2 Jelly Bean Firmware

Samsung Galaxy Note 2 (AT&T) SGH-I317 users who have already updated their devices with Android 4.1.2 Jelly Bean, may root their devices using the tutorial below.

This tutorial uses CF-Auto-Root file released by recognised XDA Developers, Chainfire. The CF-Auto-Root file allowing Galaxy Note 2 users to root their devices easily without depending on the firmware. It completely supports Android 4.1.2 Jelly Bean and future firmware as well. Head over to the CF-Auto-Root main thread to learn more about the root method.

Note: Using this root increases your flash counter. The flash counter keeps track of how many custom firmwares you have flashed, as this voids warranty. Triangle Away can be used to reset the flash counter after installing CF-Auto-Root.

Disclaimer: Rooting voids the warranty of your device. We and the developer of this rooting procedures shall not be held responsible if any undesirable outcomes may happen to your device. use of this root guide is solely at your own risk!

Pre-requisites
1. Install USB Driver for Samsung Galaxy Note 2 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options (Android 4.0 or later) or go to Settings >> Applications >> Development (Android 2.3 or earlier).
3. Make a backup of all your important data before following the guide.
4. Ensure the battery of the phone is charged more than 80 per cent.
5. The CF-Auto-Root file works only on Samsung Galaxy Note 2 (AT&T) SGH-I317. Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy Note 2 by navigating to Settings >> About Phone.

File Required
1. CF-Auto-Root for Galaxy Note 2 (AT&T) SGH-I317 (CF-Auto-Root-t0lteatt-t0lteatt-samsungsghi317.zip)
2. Odin 3.07

Steps to Root Galaxy Note 2 (AT&T) SGH-I317 Running on Android 4.1.2 Jelly Bean Firmware
Step 1: Extract CF-Auto-Root and Odin 3.07 files using winrar/7zip/winzip or any other extracting tool.
Step 2: Switch off the Galaxy Note 2. Then boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 3: Launch Odin on the computer.
Step 4: Connect the Galaxy Note 2 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added. If Odin fails to detect the device then re-install USB driver
Step 5: In Odin, click the PDA button and select the CF-Auto-Root-t0lteatt-t0lteatt-samsungsghi317.tar.md5 file.
Step 6: Verify that Auto Reboot and F.Reset Time checkboxes are selected in Odin. Also, ensure the Re-Partition option in Odin is not selected.
Step 7: Double-check and click Start in Odin. The installation process will now begin.
Step 8: Once flashing completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy Note 2 (AT&T) SGH-I317 running on Android 4.1.2 Jelly Bean firmware is now rooted successfully. You can now install any app that requires root permission. Verify the root status of the device by downloading Root Checker app from Google Play Store.

Thank's to all fellas at XDA who first tried out this rooting technique. This method was originally posted via XDA-Developers original thread.

Click here to know How to Update Galaxy Note 2 (AT&T) SGH-I317 with Android 4.1.2 Jelly Bean official firmware.

Thanks for Read How to Root Galaxy Note 2 (AT&T) SGH-I317 on Android 4.1.2 Jelly Bean Firmware Article

How to Root Galaxy Note 2 (Sprint) SPH-L900 on Android 4.1.2 Jelly Bean Firmware

Are You Looking For How to Root Galaxy Note 2 (Sprint) SPH-L900 on Android 4.1.2 Jelly Bean Firmware

Samsung Galaxy Note 2 (Sprint) SPH-L900 users who have already updated their devices with Android 4.1.2 Jelly Bean, may root their devices using the tutorial below.

This tutorial uses CF-Auto-Root file released by recognised XDA Developers, Chainfire. The CF-Auto-Root file allowing Galaxy Note 2 users to root their devices easily without depending on the firmware. It completely supports Android 4.1.2 Jelly Bean and future firmware as well. Head over to the CF-Auto-Root main thread to learn more about the root method.

Note: Using this root increases your flash counter. The flash counter keeps track of how many custom firmwares you have flashed, as this voids warranty. Triangle Away can be used to reset the flash counter after installing CF-Auto-Root.

Disclaimer: Rooting voids the warranty of your device. We and the developer of this rooting procedures shall not be held responsible if any undesirable outcomes may happen to your device. use of this root guide is solely at your own risk!

Pre-requisites
1. Install USB Driver for Samsung Galaxy Note 2 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options (Android 4.0 or later) or go to Settings >> Applications >> Development (Android 2.3 or earlier).
3. Make a backup of all your important data before following the guide.
4. Ensure the battery of the phone is charged more than 80 per cent.
5. The CF-Auto-Root file works only on Samsung Galaxy Note 2 (Sprint) SPH-L900. Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy Note 2 by navigating to Settings >> About Phone.

File Required
1. CF-Auto-Root for Galaxy Note 2 (Sprint) SPH-L900 (CF-Auto-Root-t0ltespr-t0ltespr-sphl900.zip)
2. Odin 3.07

Steps to Root Galaxy Note 2 (Sprint) SPH-L900 Running on Android 4.1.2 Jelly Bean Firmware
Step 1: Extract CF-Auto-Root and Odin 3.07 files using winrar/7zip/winzip or any other extracting tool.
Step 2: Switch off the Galaxy Note 2. Then boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 3: Launch Odin on the computer.
Step 4: Connect the Galaxy Note 2 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added. If Odin fails to detect the device then re-install USB driver
Step 5: In Odin, click the PDA button and select the CF-Auto-Root-t0ltespr-t0ltespr-sphl900.tar.md5 file.
Step 6: Verify that Auto Reboot and F.Reset Time checkboxes are selected in Odin. Also, ensure the Re-Partition option in Odin is not selected.
Step 7: Double-check and click Start in Odin. The installation process will now begin.
Step 8: Once flashing completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy Note 2 (Sprint) SPH-L900 running on Android 4.1.2 Jelly Bean firmware is now rooted successfully. You can now install any app that requires root permission. Verify the root status of the device by downloading Root Checker app from Google Play Store.

Thank's to all fellas at XDA who first tried out this rooting technique. This method was originally posted via XDA-Developers original thread.

Thanks for Read How to Root Galaxy Note 2 (Sprint) SPH-L900 on Android 4.1.2 Jelly Bean Firmware Article

How to Root Galaxy Note 2 (T-Mobile) SGH-T889 on Android 4.1.2 Jelly Bean Firmware

Are You Looking For How to Root Galaxy Note 2 (T-Mobile) SGH-T889 on Android 4.1.2 Jelly Bean Firmware

Samsung Galaxy Note 2 (T-Mobile) SGH-T889 users who have already updated their devices with Android 4.1.2 Jelly Bean, may root their devices using the tutorial below.

This tutorial uses CF-Auto-Root file released by recognised XDA Developers, Chainfire. The CF-Auto-Root file allowing Galaxy Note 2 users to root their devices easily without depending on the firmware. It completely supports Android 4.1.2 Jelly Bean and future firmware as well. Head over to the CF-Auto-Root main thread to learn more about the root method.

Note: Using this root increases your flash counter. The flash counter keeps track of how many custom firmwares you have flashed, as this voids warranty. Triangle Away can be used to reset the flash counter after installing CF-Auto-Root.

Disclaimer: Rooting voids the warranty of your device. We and the developer of this rooting procedures shall not be held responsible if any undesirable outcomes may happen to your device. use of this root guide is solely at your own risk!

Pre-requisites
1. Install USB Driver for Samsung Galaxy Note 2 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options (Android 4.0 or later) or go to Settings >> Applications >> Development (Android 2.3 or earlier).
3. Make a backup of all your important data before following the guide.
4. Ensure the battery of the phone is charged more than 80 per cent.
5. The CF-Auto-Root file works only on Samsung Galaxy Note 2 (T-Mobile) SGH-T889. Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy Note 2 by navigating to Settings >> About Phone.

File Required
1. CF-Auto-Root for Galaxy Note 2 (T-Mobile) SGH-T889 (CF-Auto-Root-t0ltetmo-t0ltetmo-sght889.zip)
2. Odin 3.07

Steps to Root Galaxy Note 2 (T-Mobile) SGH-T889 Running on Android 4.1.2 Jelly Bean Firmware
Step 1: Extract CF-Auto-Root and Odin 3.07 files using winrar/7zip/winzip or any other extracting tool.
Step 2: Switch off the Galaxy Note 2. Then boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 3: Launch Odin on the computer.
Step 4: Connect the Galaxy Note 2 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added. If Odin fails to detect the device then re-install USB driver
Step 5: In Odin, click the PDA button and select the CF-Auto-Root-t0ltetmo-t0ltetmo-sght889.tar.md5 file.
Step 6: Verify that Auto Reboot and F.Reset Time checkboxes are selected in Odin. Also, ensure the Re-Partition option in Odin is not selected.
Step 7: Double-check and click Start in Odin. The installation process will now begin.
Step 8: Once flashing completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy Note 2 (T-Mobile) SGH-T889 running on Android 4.1.2 Jelly Bean firmware is now rooted successfully. You can now install any app that requires root permission. Verify the root status of the device by downloading Root Checker app from Google Play Store.

Thank's to all fellas at XDA who first tried out this rooting technique. This method was originally posted via XDA-Developers original thread.

Thanks for Read How to Root Galaxy Note 2 (T-Mobile) SGH-T889 on Android 4.1.2 Jelly Bean Firmware Article

How to Update Galaxy Note 2 (U.S. Cellular) SCH-R950 with Android 4.1.2 VXAME2 Jelly Bean Official Firmware

Are You Looking For How to Update Galaxy Note 2 (U.S. Cellular) SCH-R950 with Android 4.1.2 VXAME2 Jelly Bean Official Firmware

An official Android 4.1.2 Jelly Bean Over-The-Air (OTA) update with base firmware VXAME2 has been released for the U.S. Cellular subscribers of Samsung Galaxy Note 2 bearing model number SCH-R950.

Firmware details
PDA: R950VXAME2
CSC: R950USCAME2
MODEM: R950VXAME2
Version: Android 4.1.2
Built date: May 13, 2013
Regions: USA (U.S. Cellular)

Samsung Galaxy Note 2 (U.S. Cellular) SCH-R950 users who missed the OTA update notification or unable to access the update over Samsung KIES, may follow our step-by-step guide to install the update manually.

Pre-requisites
1. Install USB Driver for Samsung Galaxy Note 2 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. Ensure the battery of the phone is charged more than 80 per cent.
5. The Android 4.1.2 VXAME2 Jelly Bean firmware is compatible only with Samsung Galaxy Note 2 (U.S. Cellular) SCH-R950. Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy Note 2 by navigating to Settings >> About Phone.

File Required
1. Android 4.1.2 VXAME2 Jelly Bean Firmware for Galaxy Note 2 (U.S. Cellular) SCH-R950
2. Odin 3.07

Steps to Update Galaxy Note 2 (U.S. Cellular) SCH-R950 with Android 4.1.2 VXAME2 Jelly Bean Firmware
Step 1: Extract Firmware zip file that you downloaded already from above link using winrar/7zip/winzip or any other extracting tool, you will get a .tar.md5 file and some other files.
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Power off your phone. Wait 5-6 seconds for vibration to confirm complete switch off.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy Note 2 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.
Step 7: Choose the following files in Odin from extracted R950VXAME2 firmware folder by using respective checkboxes:

• Select the PDA checkbox, and choose the file named .tar or .md5.
• Click the Phone checkbox, and choose the file with 'modem' in its name (ignore if there is no such file)
• Click the CSC checkbox, and select the file with 'csc' in its name (ignore if such file is missing)
• Choose the PIT checkbox, and choose the .pit file. Use only the file obtained during extracting in step 1 above, otherwise ignore it.

Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the START button to begin the installation process.
Step 10: Once the installation process is completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy Note 2 (U.S. Cellular) SCH-R950 should be now updated with official Android 4.1.2 VXAME2 Jelly Bean firmware. Head over to Settings >> About Phone to verify the software version running on the device.

Note: If Galaxy Note 2 (U.S. Cellular) SCH-R950 stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up, Home and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.

Click here to know How to Root Galaxy Note 2 (U.S. Cellular) SCH-R950 running on Android 4.1.2 VXAME2 Jelly Bean firmware.

Thanks for Read How to Update Galaxy Note 2 (U.S. Cellular) SCH-R950 with Android 4.1.2 VXAME2 Jelly Bean Official Firmware Article

How to Root Galaxy Note 2 (U.S. Cellular) SCH-R950 on Android 4.1.2 VXAME2 Jelly Bean Firmware

Are You Looking For How to Root Galaxy Note 2 (U.S. Cellular) SCH-R950 on Android 4.1.2 VXAME2 Jelly Bean Firmware

The U.S. Cellular subscribers of Samsung Galaxy Note 2 bearing model number SCH-R950 recently received its latest Android 4.1.2 Jelly Bean firmware update with base firmware VXAME2. The new official firmware is now available for download as an Over-The-Air (OTA) update as well as via Samsung KIES.

Samsung Galaxy Note 2 (U.S. Cellular) SCH-R950 users who have already updated their devices with Android 4.1.2 VXAME2 Jelly Bean, may root their devices using the tutorial below.

This tutorial uses CF-Auto-Root file released by recognised XDA Developers, Chainfire. The CF-Auto-Root file allowing Galaxy Note 2 users to root their devices easily without depending on the firmware. It completely supports Android 4.1.2 Jelly Bean and future firmware as well. Head over to the CF-Auto-Root main thread to learn more about the root method.

Note: Using this root increases your flash counter. The flash counter keeps track of how many custom firmwares you have flashed, as this voids warranty. Triangle Away can be used to reset the flash counter after installing CF-Auto-Root.

Disclaimer: Rooting voids the warranty of your device. We and the developer of this rooting procedures shall not be held responsible if any undesirable outcomes may happen to your device. use of this root guide is solely at your own risk!

Pre-requisites
1. Install USB Driver for Samsung Galaxy Note 2 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. Ensure the battery of the phone is charged more than 80 per cent.
5. The CF-Auto-Root file works only on Samsung Galaxy Note 2 (U.S. Cellular) SCH-R950. Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy Note 2 by navigating to Settings >> About Phone.

File Required
1. CF-Auto-Root for Galaxy Note 2 (U.S. Cellular) SCH-R950 (CF-Auto-Root-t0lteusc-t0lteusc-schr950.zip)
2. Odin 3.07

Steps to Root Galaxy Note 2 (U.S. Cellular) SCH-R950 Running on Android 4.1.2 VXAME2 Jelly Bean Firmware
Step 1: Extract CF-Auto-Root and Odin 3.07 files using winrar/7zip/winzip or any other extracting tool.
Step 2: Switch off the Galaxy Note 2. Then boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 3: Launch Odin on the computer.
Step 4: Connect the Galaxy Note 2 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added. If Odin fails to detect the device then re-install USB driver
Step 5: In Odin, click the PDA button and select the CF-Auto-Root-t0lteusc-t0lteusc-schr950.tar.md5 file.
Step 6: Verify that Auto Reboot and F.Reset Time checkboxes are selected in Odin. Also, ensure the Re-Partition option in Odin is not selected.
Step 7: Double-check and click Start in Odin. The installation process will now begin.
Step 8: Once the installation process is completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy Note 2 (U.S. Cellular) SCH-R950 running on Android 4.1.2 VXAME2 Jelly Bean firmware is now rooted successfully. You can now install any app that requires root permission. Verify the root status of the device by downloading Root Checker app from Google Play Store.

Click here to know How to Update Galaxy Note 2 (U.S. Cellular) SCH-R950 with Android 4.1.2 VXAME2 Jelly Bean official firmware.

Thanks for Read How to Root Galaxy Note 2 (U.S. Cellular) SCH-R950 on Android 4.1.2 VXAME2 Jelly Bean Firmware Article

How to Update Galaxy Note 2 N7100 with Android 4.1.2 XXDME6 Jelly Bean Official Firmware

Are You Looking For How to Update Galaxy Note 2 N7100 with Android 4.1.2 XXDME6 Jelly Bean Official Firmware

Samsung Galaxy Note 2 (GT-N7100) users in the UK have received a minor firmware update. The firmware update is still based on Android 4.1.2 Jelly Bean. According to SamMobile report, its a stability update that fixes things like battery drain, bug fixes and other small problems. The official update is currently available in most European countries as an Over-The-Air (OTA) update as well as through Samsung KIES.

Firmware details
PDA: N7100XXDME6
CSC: N7100OXXDME2
MODEM: N7100XXDME4
Version: Android 4.1.2
Built date: May 31, 2013
Regions: United Kingdom

Samsung Galaxy Note 2 N7100 users who missed the OTA update notification or unable to access the update over Samsung KIES, may follow our step-by-step guide to install the update manually.

Pre-requisites
1. Install USB Driver for Samsung Galaxy Note 2 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy Note 2 should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 per cent.
6. The Android 4.1.2 XXDME6 Jelly Bean firmware is compatible only with Samsung Galaxy Note 2 N7100. Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy Note 2 by navigating to Settings >> About Phone.

File Required
1. Android 4.1.2 XXDME6 Jelly Bean Firmware for Samsung Galaxy Note 2 N7100
2. Odin 3.07

Steps to Update Galaxy Note 2 N7100 with Android 4.1.2 XXDME6 Jelly Bean Firmware
Step 1: Extract Firmware zip file that you downloaded already from above link using winrar/7zip/winzip or any other extracting tool, you will get a .tar.md5 file and some other files.
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Power off your phone. Wait 5-6 seconds for vibration to confirm complete switch off.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy Note 2 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added. If Odin fails to detect the device then re-install USB driver.
Step 7: Choose the following files in Odin from extracted N7100XXDME6 firmware folder by using respective checkboxes:

• Select the PDA checkbox, and choose the file named .tar or .md5.
• Click the Phone checkbox, and choose the file with 'modem' in its name (ignore if there is no such file)
• Click the CSC checkbox, and select the file with 'csc' in its name (ignore if such file is missing)
• Choose the PIT checkbox, and choose the .pit file. Use only the file obtained during extracting in step 1 above, otherwise ignore it.

Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the START button to begin the installation process.
Step 10: Once the installation process is completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy Note 2 N7100 should be now updated with official Android 4.1.2 XXDME6 Jelly Bean firmware. Head over to Settings >> About Phone to verify the software version running on the device.

Note: If Galaxy Note 2 N7100 stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up, Home and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.

Click here to know How to Root Galaxy Note 2 N7100 running on Android 4.1.2 XXDME6 Jelly Bean firmware.

Thanks for Read How to Update Galaxy Note 2 N7100 with Android 4.1.2 XXDME6 Jelly Bean Official Firmware Article

How to Root Galaxy Note 2 N7100 on Android 4.1.2 XXDME6 Jelly Bean Firmware

Are You Looking For How to Root Galaxy Note 2 N7100 on Android 4.1.2 XXDME6 Jelly Bean Firmware

Samsung recently released its latest Android 4.1.2 Jelly Bean firmware update with base firmware XXDME6 for the Samsung Galaxy Note 2 bearing model number GT-N7100. The new official update is now available in most European countries as an Over-The-Air (OTA) update as well as through Samsung KIES.

Samsung Galaxy Note 2 N7100 users who have already updated their devices with Android 4.1.2 XXDME6 Jelly Bean, may root their devices using the tutorial below.

This tutorial uses CF-Auto-Root file released by recognised XDA Developers, Chainfire. The CF-Auto-Root file allowing Galaxy Note 2 users to root their devices easily without depending on the firmware. It completely supports Android 4.1.2 Jelly Bean and future firmware as well. Head over to the CF-Auto-Root main thread to learn more about the root method.

Note: Using this root increases your flash counter. The flash counter keeps track of how many custom firmwares you have flashed, as this voids warranty. Triangle Away can be used to reset the flash counter after installing CF-Auto-Root.

Disclaimer: Rooting voids the warranty of your device. We and the developer of this rooting procedures shall not be held responsible if any undesirable outcomes may happen to your device. use of this root guide is solely at your own risk!

Pre-requisites
1. Install USB Driver for Samsung Galaxy Note 2 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy Note 2 should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 per cent.
6. The CF-Auto-Root file works only on Samsung Galaxy Note 2 N7100. Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy Note 2 by navigating to Settings >> About Phone.

File Required
1. CF-Auto-Root for Galaxy Note 2 N7100 (CF-Auto-Root-t03g-t03gxx-gtn7100.zip)
2. Odin 3.07

Steps to Root Galaxy Note 2 N7100 Running on Android 4.1.2 XXDME6 Jelly Bean Firmware
Step 1: Extract CF-Auto-Root and Odin 3.07 files using winrar/7zip/winzip or any other extracting tool.
Step 2: Switch off the Galaxy Note 2. Then boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 3: Launch Odin on the computer.
Step 4: Connect the Galaxy Note 2 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added. If Odin fails to detect the device then re-install USB driver.
Step 5: In Odin, click the PDA button and select the CF-Auto-Root-t03g-t03gxx-gtn7100.tar.md5 file.
Step 6: Verify that Auto Reboot and F.Reset Time checkboxes are selected in Odin. Also, ensure the Re-Partition option in Odin is not selected.
Step 7: Double-check and click Start in Odin. The installation process will now begin.
Step 8: Once the installation process is completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy Note 2 N7100 running on Android 4.1.2 XXDME6 Jelly Bean firmware is now rooted successfully. You can now install any app that requires root permission. Verify the root status of the device by downloading Root Checker app from Google Play Store.

Thank's to all fellas at XDA who first tried out this rooting technique. This root method was originally posted via XDA-Developer original thread.

Thanks for Read How to Root Galaxy Note 2 N7100 on Android 4.1.2 XXDME6 Jelly Bean Firmware Article

How to Root Galaxy Note 2 (LTE) N7105 on Android 4.1.2 Jelly Bean Firmware

Are You Looking For How to Root Galaxy Note 2 (LTE) N7105 on Android 4.1.2 Jelly Bean Firmware

Samsung has rolled out its latest Android 4.1.2 Jelly Bean firmware update for the LTE variant of Samsung Galaxy Note 2 bearing model number GT-N7105 in several countries. The new official firmware is now available for download as an Over-The-Air (OTA) update as well as via Samsung KIES.

Samsung Galaxy Note 2 (LTE) N7105 users who have already installed their devices with Android 4.1.2 Jelly Bean, may root their devices using the tutorial below.

This tutorial uses CF-Auto-Root file released by recognised XDA Developers, Chainfire. The CF-Auto-Root file allowing Galaxy Note 2 users to root their devices easily without depending on the firmware. It completely supports Android 4.1.2 Jelly Bean and future firmware as well. Head over to the CF-Auto-Root main thread to learn more about the root method.

Note: Using this root increases your flash counter. The flash counter keeps track of how many custom firmwares you have flashed, as this voids warranty. Triangle Away can be used to reset the flash counter after installing CF-Auto-Root.

Disclaimer: Rooting voids the warranty of your device. We and the developer of this rooting procedures shall not be held responsible if any undesirable outcomes may happen to your device. use of this root guide is solely at your own risk!

Pre-requisites
1. Install USB Driver for Samsung Galaxy Note 2 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. Ensure the battery of the tablet is charged more than 80 per cent.
5. The CF-Auto-Root file works only on Samsung Galaxy Note 2 (LTE) N7105. Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy Note 2 by navigating to Settings >> About Phone.

File Required
1. CF-Auto-Root for Galaxy Note 2 (LTE) N7105 (CF-Auto-Root-t0lte-t0ltexx-gtn7105.zip)
2. Odin 3.07

Steps to Root Galaxy Note 2 (LTE) N7105 Running on Android 4.1.2 Jelly Bean Firmware
Step 1: Extract CF-Auto-Root and Odin 3.07 files using winrar/7zip/winzip or any other extracting tool.
Step 2: Switch off the Galaxy Note 2. Then boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 3: Launch Odin on the computer.
Step 4: Connect the Galaxy Note 2 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added. If Odin fails to detect the device then re-install USB driver
Step 5: In Odin, click the PDA button and select the CF-Auto-Root-t0lte-t0ltexx-gtn7105.tar.md5 file.
Step 6: Verify that Auto Reboot and F.Reset Time checkboxes are selected in Odin. Also, ensure the Re-Partition option in Odin is not selected.
Step 7: Double-check and click Start in Odin. The installation process will now begin.
Step 8: Once the installation process is completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy Note 2 (LTE) N7105 running on Android 4.1.2 Jelly Bean firmware is now rooted successfully. You can now install any app that requires root permission. Verify the root status of the device by downloading Root Checker app from Google Play Store.

Thank's to all fellas at XDA who first tried out this rooting technique. This method was originally posted via XDA-Developers original thread.

Thanks for Read How to Root Galaxy Note 2 (LTE) N7105 on Android 4.1.2 Jelly Bean Firmware Article

How to Update Galaxy Note 8.0 (Wi-Fi) N5110 with Android 4.1.2 UEEMF1 Jelly Bean Official Firmware

Are You Looking For How to Update Galaxy Note 8.0 (Wi-Fi) N5110 with Android 4.1.2 UEEMF1 Jelly Bean Official Firmware

Samsung has delivered a new Android 4.1.2 Jelly Bean firmware update to United States owners of the Samsung Galaxy Note 8.0 Wi-Fi Only (GT-N5110) with its build number N5110UEEMF1. The new official update is currently available as an Over-The-Air (OTA) update as well as through Samsung KIES.

Firmware details
PDA: N5110UEEMF1
CSC: N5110XAREMF1
MODEM: N5110UEEMF1
Version: Android 4.1.2
Built date: Jun 04, 2013
Regions: United States

Samsung Galaxy Note 8.0 (Wi-Fi) N5110 users who missed the OTA update notification or unable to access the update over Samsung KIES, may follow our step-by-step guide to install the update manually.

Pre-requisites
1. Install USB Driver for Samsung Galaxy Note 8.0 (Wi-Fi) on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. Ensure the battery of the phone is charged more than 80 per cent.
5. The Android 4.1.2 UEEMF1 Jelly Bean firmware is compatible only with Samsung Galaxy Note 8.0 (Wi-Fi) N5110. Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy Note 8.0 (Wi-Fi) by navigating to Settings >> About Phone.

File Required
1. Android 4.1.2 UEEMF1 Jelly Bean Firmware for Galaxy Note 8.0 (Wi-Fi) N5110
2. Odin 3.07

Steps to Update Galaxy Note 8.0 (Wi-Fi) N5110 with Android 4.1.2 UEEMF1 Jelly Bean Firmware
Step 1: Extract Firmware zip file that you downloaded already from above link using winrar/7zip/winzip or any other extracting tool, you will get a .tar.md5 file and some other files.
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Power off your phone. Wait 5-6 seconds for vibration to confirm complete switch off.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy Note 8.0 (Wi-Fi) to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added. If Odin fails to detect the device then re-install USB driver.
Step 7: Choose the following files in Odin from extracted N5110UEEMF1 firmware folder by using respective checkboxes:

• Select the PDA checkbox, and choose the file named .tar or .md5.
• Click the Phone checkbox, and choose the file with 'modem' in its name (ignore if there is no such file)
• Click the CSC checkbox, and select the file with 'csc' in its name (ignore if such file is missing)
• Choose the PIT checkbox, and choose the .pit file. Use only the file obtained during extracting in step 1 above, otherwise ignore it.

Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the START button to begin the installation process.
Step 10: Once the installation process is completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy Note 8.0 (Wi-Fi) N5110 should be now updated with official Android 4.1.2 UEEMF1 Jelly Bean firmware. Head over to Settings >> About Phone to verify the software version running on the device.

Note: If Galaxy Note 8.0 (Wi-Fi) N5110 stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up, Home and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.

Click here to know How to Root Galaxy Note 8.0 (Wi-Fi) N5110 running on Android 4.1.2 UEEMF1 Jelly Bean firmware.

Thanks for Read How to Update Galaxy Note 8.0 (Wi-Fi) N5110 with Android 4.1.2 UEEMF1 Jelly Bean Official Firmware Article

How to Update Galaxy Note 8.0 (Wi-Fi) N5110 with Android 4.1.2 XXBMF1 Jelly Bean Official Firmware

Are You Looking For How to Update Galaxy Note 8.0 (Wi-Fi) N5110 with Android 4.1.2 XXBMF1 Jelly Bean Official Firmware

UK owners of the Samsung Galaxy Note 8.0 WiFi Only (GT-5110) have received a new Android 4.1.2 Jelly Bean update build number N5110XXBMF1. The new official update is currently available as an Over-The-Air (OTA) update as well as through Samsung KIES.

Firmware details
PDA: N5110XXBMF1
CSC: N5110OXABME5
MODEM: N5110XXBMF1
Version: Android 4.1.2
Built date: Jun 04, 2013
Regions: United Kingdom

Samsung Galaxy Note 8.0 (Wi-Fi) N5110 users who missed the OTA update notification or unable to access the update over Samsung KIES, may follow our step-by-step guide to install the update manually.

Pre-requisites
1. Install USB Driver for Samsung Galaxy Note 8.0 (Wi-Fi) on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. Ensure the battery of the phone is charged more than 80 per cent.
5. The Android 4.1.2 XXBMF1 Jelly Bean firmware is compatible only with Samsung Galaxy Note 8.0 (Wi-Fi) N5110. Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy Note 8.0 (Wi-Fi) by navigating to Settings >> About Phone.

File Required
1. Android 4.1.2 XXBMF1 Jelly Bean Firmware for Galaxy Note 8.0 (Wi-Fi) N5110
2. Odin 3.07

Steps to Update Galaxy Note 8.0 (Wi-Fi) N5110 with Android 4.1.2 XXBMF1 Jelly Bean Firmware
Step 1: Extract Firmware zip file that you downloaded already from above link using winrar/7zip/winzip or any other extracting tool, you will get a .tar.md5 file and some other files.
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Power off your phone. Wait 5-6 seconds for vibration to confirm complete switch off.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy Note 8.0 (Wi-Fi) to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added. If Odin fails to detect the device then re-install USB driver.
Step 7: Choose the following files in Odin from extracted N5110XXBMF1 firmware folder by using respective checkboxes:

• Select the PDA checkbox, and choose the file named .tar or .md5.
• Click the Phone checkbox, and choose the file with 'modem' in its name (ignore if there is no such file)
• Click the CSC checkbox, and select the file with 'csc' in its name (ignore if such file is missing)
• Choose the PIT checkbox, and choose the .pit file. Use only the file obtained during extracting in step 1 above, otherwise ignore it.

Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the START button to begin the installation process.
Step 10: Once the installation process is completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy Note 8.0 (Wi-Fi) N5110 should be now updated with official Android 4.1.2 XXBMF1 Jelly Bean firmware. Head over to Settings >> About Phone to verify the software version running on the device.

Note: If Galaxy Note 8.0 (Wi-Fi) N5110 stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up, Home and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.

Click here to know How to Root Galaxy Note 8.0 (Wi-Fi) N5110 running on Android 4.1.2 XXBMF1 Jelly Bean firmware.

Thanks for Read How to Update Galaxy Note 8.0 (Wi-Fi) N5110 with Android 4.1.2 XXBMF1 Jelly Bean Official Firmware Article

How to Root Galaxy Note 8.0 (Wi-Fi) N5110 on Android 4.1.2 Jelly Bean Firmware

Are You Looking For How to Root Galaxy Note 8.0 (Wi-Fi) N5110 on Android 4.1.2 Jelly Bean Firmware

Samsung has released another Android 4.1.2 Jelly Bean firmware update for the Wi-Fi only version of Galaxy Note 8.0 bearing model number GT-N5110 in several countries. The new official firmware is now available as an Over-The-Air (OTA) update as well as through Samsung KIES.

Samsung Galaxy Note 8.0 (Wi-Fi) N5110 users who have already installed their devices with Android 4.1.2 Jelly Bean, may root their devices using the tutorial below.

This tutorial uses CF-Auto-Root file released by recognised XDA Developers, Chainfire. The CF-Auto-Root file allowing Galaxy Note 8.0 (Wi-Fi) users to root their devices easily without depending on the firmware. It completely supports Android 4.1.2 Jelly Bean and future firmware as well. Head over to the CF-Auto-Root main thread to learn more about the root method.

Note: Using this root increases your flash counter. The flash counter keeps track of how many custom firmwares you have flashed, as this voids warranty. Triangle Away can be used to reset the flash counter after installing CF-Auto-Root.

Disclaimer: Rooting voids the warranty of your device. We and the developer of this rooting procedures shall not be held responsible if any undesirable outcomes may happen to your device. use of this root guide is solely at your own risk!

Pre-requisites
1. Install USB Driver for Samsung Galaxy Note 8.0 (Wi-Fi) on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. Ensure the battery of the phone is charged more than 80 per cent.
5. The CF-Auto-Root file works only on Samsung Galaxy Note 8.0 (Wi-Fi) N5110. Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy Note 8.0 (Wi-Fi) by navigating to Settings >> About Phone.

File Required
1. CF-Auto-Root for Galaxy Note 8.0 (Wi-Fi) N5110 (CF-Auto-Root-konawifi-konawifixx-gtn5110.zip)
2. Odin 3.07

Steps to Root Galaxy Note 8.0 (Wi-Fi) N5110 Running on Android 4.1.2 Jelly Bean Firmware
Step 1: Extract CF-Auto-Root and Odin 3.07 files using winrar/7zip/winzip or any other extracting tool.
Step 2: Switch off the Galaxy Note 8.0 (Wi-Fi). Then boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 3: Launch Odin on the computer.
Step 4: Connect the Galaxy Note 8.0 (Wi-Fi) to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added. If Odin fails to detect the device then re-install USB driver
Step 5: In Odin, click the PDA button and select the CF-Auto-Root-konawifi-konawifixx-gtn5110.tar.md5 file.
Step 6: Verify that Auto Reboot and F.Reset Time checkboxes are selected in Odin. Also, ensure the Re-Partition option in Odin is not selected.
Step 7: Double-check and click Start in Odin. The installation process will now begin.
Step 8: Once the installation process is completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy Note 8.0 (Wi-Fi) N5110 running on Android 4.1.2 Jelly Bean firmware is now rooted successfully. You can now install any app that requires root permission. Verify the root status of the device by downloading Root Checker app from Google Play Store.

Thank's to all fellas at XDA who first tried out this rooting technique. This method was originally posted via XDA-Developers original thread.

Thanks for Read How to Root Galaxy Note 8.0 (Wi-Fi) N5110 on Android 4.1.2 Jelly Bean Firmware Article

How to Root Galaxy Note 8.0 (LTE) N5120 on Android 4.1.2 Jelly Bean Firmware

Are You Looking For How to Root Galaxy Note 8.0 (LTE) N5120 on Android 4.1.2 Jelly Bean Firmware

Samsung recently released Android 4.1.2 Jelly Bean firmware update for the LTE variant of Galaxy Note 8.0 bearing model number GT-N5120 in several countries. The new official firmware is now available for download through Samsung KIES as well as Over-The-Air (OTA) update.

Samsung Galaxy Note 8.0 (LTE) N5120 users who have already installed their devices with Android 4.1.2 Jelly Bean, may root their devices using the tutorial below.

This tutorial uses CF-Auto-Root file released by recognised XDA Developers, Chainfire. The CF-Auto-Root file allowing Galaxy Note 8.0 users to root their devices easily without depending on the firmware. It completely supports Android 4.1.2 Jelly Bean and future firmware as well. Head over to the CF-Auto-Root main thread to learn more about the root method.

Note: Using this root increases your flash counter. The flash counter keeps track of how many custom firmwares you have flashed, as this voids warranty. Triangle Away can be used to reset the flash counter after installing CF-Auto-Root.

Disclaimer: Rooting voids the warranty of your device. We and the developer of this rooting procedures shall not be held responsible if any undesirable outcomes may happen to your device. use of this root guide is solely at your own risk!

Pre-requisites
1. Install USB Driver for Samsung Galaxy Note 8.0 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. Ensure the battery of the phone is charged more than 80 per cent.
5. The CF-Auto-Root file works only on Samsung Galaxy Note 8.0 (LTE) N5120. Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy Note 8.0 by navigating to Settings >> About Phone.

File Required
1. CF-Auto-Root for Galaxy Note 8.0 (LTE) N5120 (CF-Auto-Root-konalte-konaltexx-gtn5120.zip)
2. Odin 3.07

Steps to Root Galaxy Note 8.0 (LTE) N5120 Running on Android 4.1.2 Jelly Bean Firmware
Step 1: Extract CF-Auto-Root and Odin 3.07 files using winrar/7zip/winzip or any other extracting tool.
Step 2: Switch off the Galaxy Note 8.0. Then boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 3: Launch Odin on the computer.
Step 4: Connect the Galaxy Note 8.0 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added. If Odin fails to detect the device then re-install USB driver
Step 5: In Odin, click the PDA button and select the CF-Auto-Root-konalte-konaltexx-gtn5120.tar.md5 file.
Step 6: Verify that Auto Reboot and F.Reset Time checkboxes are selected in Odin. Also, ensure the Re-Partition option in Odin is not selected.
Step 7: Double-check and click Start in Odin. The installation process will now begin.
Step 8: Once the installation process is completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy Note 8.0 (LTE) N5120 running on Android 4.1.2 Jelly Bean firmware is now rooted successfully. You can now install any app that requires root permission. Verify the root status of the device by downloading Root Checker app from Google Play Store.

Thank's to all fellas at XDA who first tried out this rooting technique. This method was originally posted via XDA-Developers original thread.

Thanks for Read How to Root Galaxy Note 8.0 (LTE) N5120 on Android 4.1.2 Jelly Bean Firmware Article