How to Update Galaxy S4 I9500 with Android 4.2.2 XXUAMDL Jelly Bean Official Firmware

Are You Looking For How to Update Galaxy S4 I9500 with Android 4.2.2 XXUAMDL Jelly Bean Official Firmware

An official software Over-The-Air (OTA) update is rolling out for the international version of Samsung Galaxy S4 GT-I9500 with base firmware XXUAMDL. The XXUAMDL build is an unbranded version of firmware which means it can be installed on any Galaxy S4 I9500 unit.

Firmware details
PDA: I9500XXUAMDL
CSC: I9500OLBAMDK
Version: Android 4.2.2
Built date: April, 2013
Regions: Indonesia, Malaysia, Philippines, Singapore, Vietnam, Thailand

The Galaxy S4 users, who cannot access Over-The-Air (OTA) update notification or download the update through Samsung KIES, can now download and install the same manually using our step-by-step guide given below.

Pre-requisites
1. Install USB Driver for Samsung  Galaxy S4 on the computer.
2. Enable USB Debugging Mode.
3. Make a backup of all your important data before following the guide.
4. The  Galaxy S4 should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 per cent.
6. The Android 4.2.2 XXUAMDL Jelly Bean firmware is compatible only with Samsung  Galaxy S4 I9500 and installing this on any incorrect variant will brick the device. Therefore, verify the model number of the  Galaxy S4 by navigating to Settings>> About Phone.

File Required
1. Android 4.2.2 XXUAMDL Jelly Bean Firmware
2. Odin 3.07

Steps to Update  Galaxy S4 I9500 with Android 4.2.2 XXUAMDL Jelly Bean Firmware
Step 1: Extract Firmware zip file that you downloaded already from above link, you will get a .tar.md5 file and some other files.
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Power off your phone. Wait 5-6 seconds for vibration to confirm complete switch off.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the  Galaxy S4 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added. If Odin fails to detect the device then re-install USB driver.
Step 7: Choose the following files in Odin from extracted I9500XXUAMDL firmware folder by using respective checkboxes:

• Select the PDA checkbox, and choose the file named .tar or .md5.
• Click the Phone checkbox, and choose the file with 'modem' in its name (ignore if there is no such file)
• Click the CSC checkbox, and select the file with 'csc' in its name (ignore if such file is missing)
• Choose the PIT checkbox, and choose the .pit file. Use only the file obtained during extracting in step 1 above, otherwise ignore it.

Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the START button to begin the flashing process.
Step 10: Once flashing completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung  Galaxy S4 I9500 should be now updated with official Android 4.2.2 XXUAMDL Jelly Bean. Head over to Settings>> About Phone to verify the software version running on the device.

Note: If  Galaxy S4 I9500 stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up, Home and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.

Click here to know How to Root Galaxy S4 I9500 running on Android 4.2.2 XXUAMDL Jelly Bean firmware.

Thanks for Read How to Update Galaxy S4 I9500 with Android 4.2.2 XXUAMDL Jelly Bean Official Firmware Article

How to Root Galaxy S4 I9500 on Android 4.2.2 XXUAMDL Jelly Bean Firmware

Are You Looking For How to Root Galaxy S4 I9500 on Android 4.2.2 XXUAMDL Jelly Bean Firmware

Samsung has released its latest Android 4.2.2 Jelly Bean firmware update with base firmware XXUAMDL on the Exynos 5 octa-core variant of Samsung Galaxy S4 bearing model number GT-I9500. The official firmware is now available for download in select Southeast Asia countries as an Over-The-Air (OTA) update as well as via Samsung KIES.

Samsung Galaxy S4 I9500 users who have already updated their devices with Android 4.2.2 XXUAMDL Jelly Bean, may root their devices using the tutorial below.

Disclaimer: Rooting voids the warranty of your device. We and the developer of this rooting procedures shall not be held responsible if any undesirable outcomes may happen to your device. use of this root guide is solely at your own risk!

Pre-requisites
1) Install USB Driver for Samsung Galaxy S4 on the computer.
2) Enable USB Debugging Mode on the phone.
3) Make a backup of all your important data before following the guide.
4) The Galaxy S4 I9500 should be factory unlocked and not locked to any particular carrier.
5) Ensure the battery of the phone is charged more than 80 per cent.
6) The stock recovery package works only on Samsung Galaxy S4 I9500 running on Android 4.2.2 XXUAMDE Jelly Bean. Applying this on any incorrect variant will brick the device. Verify the model number of the Galaxy S4 by selecting Settings >> About Phone.

Steps to root Galaxy S4 I9500 on Android 4.2.2 XXUAMDL Jelly Bean Firmware
Step 1: Download the SamsungI9500_cwm_Recovery_by cofface_0503.zip file for Samsung Galaxy S4 to the computer and extract using winrar/7zip/winzip or any other extracting tool.
Step 2: Download Odin 3.07 and extract the zip file
Step 3: Switch off the Galaxy S4. Then boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode
Step 4: Launch Odin on the computer.
Step 5: Connect the Galaxy S4 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added. If Odin fails to detect the device then re-install USB driver.
Step 6: In Odin, click the PDA button and select the cofface_samsungI9500_recovery_en_0503.tar file
Step 7: Verify that Auto Reboot and F.Reset Time checkboxes are selected in Odin. DO NOT Tick "Re-partition" options.
Step 8: Finally hit the Start button in Odin to begin the flashing. The installation will take some time
Step 9: When the installation process is completed the phone will restart automatically. Once the home screen appears on the phone users may safely unplug the device from the computer
Step 10: Switch off the Galaxy S4. Then boot the phone into recovery mode by pressing and holding Volume Up, Home and Power buttons together and select ROOT YOUR PHONE.
Step 11: Once rooting process is completed, return to main recovery menu and select reboot system now to reboot phone.

Samsung Galaxy S4 I9500 running on official Android 4.2.2 XXUAMDL Jelly Bean is now rooted successfully. You can now install any app that requires root permission.

[Note: If this method doesn't work try Adam Kernel (including AutoRoot with SuperSU v1.25) or Chainfire's CF-Auto-Root methods.]

Thank's to all fellas at XDA who first tried out this rooting technique. This root method was originally posted via XDA-Developers original thread.

Thanks for Read How to Root Galaxy S4 I9500 on Android 4.2.2 XXUAMDL Jelly Bean Firmware Article

How to Update Galaxy Grand Duos I9082 with Android 4.1.2 XXAMCE Jelly Bean Official Firmware

Are You Looking For How to Update Galaxy Grand Duos I9082 with Android 4.1.2 XXAMCE Jelly Bean Official Firmware

Samsung recently started rolling out its official Android 4.1.2 Jelly Bean update for the Galaxy Grand Duos GT-I9082 in several countries. The new official firmware is now available for download through Samsung KIES as well as Over-The-Air (OTA) update in Southeast Asia countries - Indonesia, Malaysia, Philippines, Singapore, Vietnam and Thailand.

Firmware details
PDA: I9082XXAMCE
CSC: I9082OLBAMC4
Version: Android 4.1.2
Built date: March, 2013
Regions: Indonesia, Malaysia, Philippines, Singapore, Vietnam, Thailand

The Galaxy Grand Duos users who missed the OTA update notification and those who are residing outside the supported countries can manually download and install the same using our step-by-step guide given below.

Pre-requisites
1. Install USB Driver for Samsung Galaxy Grand Duos on the computer.
2. Enable USB Debugging Mode.
3. Make a backup of all your important data before following the guide.
4. The Galaxy Grand Duos should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 per cent.
6. The Android 4.1.2 XXAMCE Jelly Bean firmware is compatible only with Samsung Galaxy Grand Duos I9082 and installing this on any incorrect variant will brick the device. Therefore, verify the model number of the Galaxy Grand Duos by navigating to Settings>> About Phone.

File Required
1. Android 4.1.2 XXAMCE Jelly Bean Firmware
2. Odin 3.07

Steps to Update Galaxy Grand Duos I9082 on Android 4.1.2 XXAMCE Jelly Bean Firmware
Step 1: Extract Firmware zip file that you downloaded already from above link, you will get a .tar.md5 file and some other files.
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Power off your phone. Wait 5-6 seconds for vibration to confirm complete switch off.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy Grand Duos to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added. If Odin fails to detect the device then re-install USB driver.
Step 7: Choose the following files in Odin from extracted I9082XXAMCE firmware folder by using respective checkboxes:

• Select the PDA checkbox, and choose the file named .tar or .md5.
• Click the Phone checkbox, and choose the file with 'modem' in its name (ignore if there is no such file)
• Click the CSC checkbox, and select the file with 'csc' in its name (ignore if such file is missing)
• Choose the PIT checkbox, and choose the .pit file. Use only the file obtained during extracting in step 1 above, otherwise ignore it.

Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the START button to begin the flashing process.
Step 10: Once flashing completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy Grand Duos I9082 should be now updated with official Android 4.1.2 XXAMCE Jelly Bean. Head over to Settings>> About Phone to verify the software version running on the device.

Note: If Galaxy Grand Duos I9082 stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up, Home and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.

Click here to know How to Root Galaxy Grand Duos I9082 running on Android 4.1.2 XXAMCE Jelly Bean firmware.

Thanks for Read How to Update Galaxy Grand Duos I9082 with Android 4.1.2 XXAMCE Jelly Bean Official Firmware Article

How to Root Galaxy Grand Duos I9082 on Android 4.1.2 XXAMCE Jelly Bean Firmware

Are You Looking For How to Root Galaxy Grand Duos I9082 on Android 4.1.2 XXAMCE Jelly Bean Firmware

Samsung recently released its official Android 4.1.2 Jelly Bean update with firmware build number I9082XXAMCE for Galaxy Grand Duos bearing model number GT-I9082. The firmware is now available for download via Samsung KIES as well as Over-The-Air (OTA) in Southeast Asia regions.

Samsung Galaxy Grand Duos I9082 users who have already updated their devices with Android 4.1.2 XXAMCE Jelly Bean firmware, may root their devices using the tutorial below.

Disclaimer: Rooting voids the warranty of your device. We and the developer of this rooting procedures shall not be held responsible if any undesirable outcomes may happen to your device. use of this root guide is solely at your own risk!

Pre-Requisites
1. Install USB Driver for Samsung Galaxy Grand Duos on your computer.
2. Enable USB Debugging Mode. [Press Menu >> Settings >> Applications. From there navigate and tap on Development option and ensure the USB Debugging is turned on.]
3. Make a backup of all your important data before following the guide.
4. The Galaxy Grand Duos should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 per cent.
6. The Recovery file and the SuperSU files used for rooting are compatible only with the Samsung Galaxy Grand Duos I9082. Applying theses on any incorrect variant will brick the device. Verify the model number of the Galaxy Grand Duos by selecting Settings >> About Phone.

File Required
1. Odin3_v3.07.rar
2. CWM-touch_i9082_chotu.tar.zip
3. Fix-Recovery.zip
4. UPDATE-SuperSU-v1.25.zip

Steps to Install CWM Recovery on Samsung Galaxy Grand Duos I9082
Step 1: Extract Odin3_v3.07.rar and CWM-touch_i9082_chotu.tar.zip files using winrar/7zip/winzip or any other extracting tool.
Step 2: Copy Fix-Recovery.zip and UPDATE-SuperSU-v1.25.zip files to external SD card of phone.
Step 3: Switch off the Galaxy Grand Duos. Then boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 4: Run Odin on your computer.
Step 5: Connect the phone to the computer using the USB cable while the device is in the Download Mode. A message saying Added will arrive under Odin's message box in the bottom left. You will also get to see COM port with a number in Yellow when the phone is connected to the computer successfully.
Step 6: In Odin, click the PDA and select the CWM-touch_i9082_chotu.tar.md5 file. Also, ensure the Auto-Reboot and Re-Partition options in Odin is not selected.
Step 7: Double-check and click Start in Odin. The installation process will now begin.
Step 8: Once installation is completed, switch off the phone manually (Take out the battery). Then unplug the USB cable to disconnect it from computer.

Steps to Root Galaxy Grand Duos I9082 by Installing SuperSU via CWM Recovery
Step 9: Boot the phone into CWM Recovery by pressing and holding Volume Up + Home buttons together and then press the Power button until the device turns on.
Note: This should boot in CWM Recovery if you manually switch off the phone in Step-8.
Step 10: Now select install zip from sdcard, select choose zip from sdcard and then navigate to the Fix-Recovery.zip file. Select and confirm installation by selecting Yes.
Step 11: Return to main recovery menu and repeat Step 10 but this time choose UPDATE-SuperSU-v1.25.zip file.
Step 12: Once installation process is completed, return to main recovery menu and select reboot system now to reboot phone.

The Samsung Galaxy Grand Duos I9082, running official Android 4.1.2 XXAMCE Jelly Bean, is now rooted successfully.

Thank's to all fellas at XDA who first tried out this rooting technique. This root method was originally posted via XDA-Developers original thread.

Thanks for Read How to Root Galaxy Grand Duos I9082 on Android 4.1.2 XXAMCE Jelly Bean Firmware Article

How to Update Galaxy Note 2 N7100 with Android 4.1.2 XXDME1 Jelly Bean Official Firmware

Are You Looking For How to Update Galaxy Note 2 N7100 with Android 4.1.2 XXDME1 Jelly Bean Official Firmware

Samsung recently rolled out its latest official Jelly Bean update, Android 4.1.2 with base firmware XXDME1, for Galaxy Note 2 GT-N7100 users in Southeast Asia countries - Indonesia, Malaysia, Philippines, Singapore,Vietnam and Thailand.

Firmware details
PDA: N7100XXDME1
CSC: N7100OLBDMD2
Version: Android 4.1.2
Built date: May, 2013
Regions: Indonesia, Malaysia, Philippines, Singapore, Vietnam, Thailand

The official firmware is now available for download via Over-The-Air (OTA) update as well as through Samsung KIES. However, those who fail to upgrade their devices using official method, may follow our step-by-step guide to install the update manually.

Pre-requisites
1. Install USB Driver for Samsung Galaxy Note on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy Note 2 should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 per cent.
6. The Android 4.1.2 XXDME1 Jelly Bean firmware is compatible only with Samsung Galaxy Note 2 N7100. Installing this on any incorrect variant will brick the device. Verify the model number of the Galaxy Note 2 by navigating to Settings >> About Phone.

File Required
1. Android 4.1.2 XXDME1 Jelly Bean Firmware
2. Odin 3.07

Steps to Update Galaxy Note 2 N7100 with Android 4.1.2 XXDME1 Jelly Bean Firmware
Step 1: Extract Firmware zip file that you downloaded already from above link, you will get a .tar.md5 file and some other files.
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Power off your phone. Wait 5-6 seconds for vibration to confirm complete switch off.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy Note 2 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added. If Odin fails to detect the device then re-install USB driver.
Step 7: Choose the following files in Odin from extracted N7100XXDME1 firmware folder by using respective checkboxes:

• Select the PDA checkbox, and choose the file named .tar or .md5.
• Click the Phone checkbox, and choose the file with 'modem' in its name (ignore if there is no such file)
• Click the CSC checkbox, and select the file with 'csc' in its name (ignore if such file is missing)
• Choose the PIT checkbox, and choose the .pit file. Use only the file obtained during extracting in step 1 above, otherwise ignore it.

Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the START button to begin the flashing process.
Step 10: Once flashing completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung Galaxy Note 2 N7100 should be now updated with official Android 4.1.2 XXDME1 Jelly Bean. Head over to Settings >> About Phone to verify the software version running on the device.

Note: If Galaxy Note 2 N7100 stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up, Home and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.

Click here to know How to Root Galaxy Note 2 N7100 running on Android 4.1.2 XXDME1 Jelly Bean firmware.

Thanks for Read How to Update Galaxy Note 2 N7100 with Android 4.1.2 XXDME1 Jelly Bean Official Firmware Article

How to Root Galaxy Note 2 N7100 on Android 4.1.2 XXDME1 Jelly Bean Firmware

Are You Looking For How to Root Galaxy Note 2 N7100 on Android 4.1.2 XXDME1 Jelly Bean Firmware

Samsung Galaxy Note 2 N7100 users who have already updated their devices with Android 4.1.2 XXDME1 Jelly Bean firmware, may root their devices using the tutorial below.

This tutorial uses CF-Auto-Root file released by recognised XDA Developers, Chainfire. The CF-Auto-Root file allowing Galaxy Note 2 users to root their devices easily without depending on the firmware. It completely supports Android 4.1.2 Jelly Bean and future firmware as well.

Disclaimer: Rooting voids the warranty of your device. We and the developer of this rooting procedures shall not be held responsible if any undesirable outcomes may happen to your device. use of this root guide is solely at your own risk!

Pre-requisites
1. Install USB Driver for Samsung Galaxy Note on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The Galaxy Note 2 should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 per cent.
6. The CF-Auto-Root file works only on Samsung Galaxy Note 2 N7100. Applying this on any incorrect variant will brick the device. Verify the model number of the Galaxy Note 2 by navigating to Settings >> About Phone.

File Required
1. CF-Auto-Root for Galaxy Note 2 N7100  (CF-Auto-Root-t03g-t03gxx-gtn7100.zip)
2. Odin 3.07

Steps to Root Galaxy Note 2 N7100 on Android 4.1.2 XXDME1 Jelly Bean Firmware
Step 1: Extract downloaded CF-Auto-Root zip file and you will find a .tar.md5 file within it.
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Power off your phone. Wait 5-6 seconds for vibration to confirm complete switch off.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the Galaxy Note 2 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added. If Odin fails to detect the device then re-install USB driver.
Step 7: Select these files in Odin at respective buttons:

• Click the PDA Button, and select CF-Auto-Root-t03g-t03gxx-gtn7100.tar.md5.

Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the START button to begin the flashing process.
Step 10: Once flashing completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Your Samsung Galaxy Note 2 N7100 running on Android 4.1.2 XXDME1 Jelly Bean firmware is now rooted successfully. You may now install any app that requires root permission.

Thank's to all fellas at XDA who first tried out this rooting technique. This root method was originally posted via XDA-Developer original thread.

Thanks for Read How to Root Galaxy Note 2 N7100 on Android 4.1.2 XXDME1 Jelly Bean Firmware Article

How to Update Galaxy Note 8.0 N5100 with Android 4.1.2 XXBMD1 Jelly Bean Official Firmware

Are You Looking For How to Update Galaxy Note 8.0 N5100 with Android 4.1.2 XXBMD1 Jelly Bean Official Firmware

Samsung recently released its latest official Android 4.1.2 Jelly Bean update with base firmware XXBMD1 for the international version of Galaxy Note 8.0 bearing model number GT-N5100.

Firmware details
PDA: N5100XXBMD1
CSC: N5100OLBBMC8
Version: Android 4.1.2
Built date: April, 2013
Regions: Indonesia, Malaysia, Philippines, Singapore, Vietnam, Thailand

The official firmware is now available for download via Over-The-Air (OTA) update as well as through Samsung KIES. However, those who fail to upgrade their devices with Android 4.1.2 XXBMD1 Jelly Bean using official method, may follow our step-by-step guide to install the update manually.

Pre-requisites
1. Install USB Driver for Samsung  Galaxy Note 8.0 on the computer.
2. Enable USB Debugging Mode on the phone by navigating to Settings >> Developer Options.
3. Make a backup of all your important data before following the guide.
4. The  Galaxy Note 8.0 should be factory unlocked and not locked to any particular carrier.
5. Ensure the battery of the phone is charged more than 80 per cent.
6. The Android 4.1.2 XXBMD1 Jelly Bean firmware is compatible only with Samsung Galaxy Note 8.0 N5100. Applying this to any incorrect variant might brick the device. Verify the model number of the Galaxy Note 8.0 by navigating to Settings >> About Phone.

File Required
1. Android 4.1.2 XXBMD1 Jelly Bean Firmware
2. Odin 3.07

Steps to Update Galaxy Note 8.0 N5100 with Android 4.1.2 XXBMD1 Jelly Bean Firmware
Step 1: Extract Firmware zip file that you downloaded already from above link, you will get a .tar.md5 file and some other files.
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 3: Power off your phone. Wait 5-6 seconds for vibration to confirm complete switch off.
Step 4: Boot the device into Download Mode by pressing and holding Volume Down + Home buttons together and then press the Power button until the device turns on. Now press the Volume Up button to enter Download Mode.
Step 5: Run Odin on the computer as an Administrator.
Step 6: Connect the  Galaxy Note 8.0 to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn yellow with the COM port number. Additionally, the successful connected will be indicated by a message saying Added. If Odin fails to detect the device then re-install USB driver.
Step 7: Choose the following files in Odin from extracted N5100XXBMD1 firmware folder by using respective checkboxes:

• Select the PDA checkbox, and choose the file named .tar or .md5.
• Click the Phone checkbox, and choose the file with 'modem' in its name (ignore if there is no such file)
• Click the CSC checkbox, and select the file with 'csc' in its name (ignore if such file is missing)
• Choose the PIT checkbox, and choose the .pit file. Use only the file obtained during extracting in step 1 above, otherwise ignore it.

Step 8: In Odin, enable Auto Reboot and F. Reset Time checkboxes. Also, ensure the Re-Partition checkbox is chosen only if a .pit file was chosen in the previous step.
Step 9: Verify everything suggested in Step 7 and Step 8 is done correctly. Then hit the START button to begin the flashing process.
Step 10: Once flashing completed, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from computer.

Samsung  Galaxy Note 8.0 N5100 should be now updated with official Android 4.1.2 XXBMD1 Jelly Bean. Head over to Settings >> About Phone to verify the software version running on the device.

Note: If  Galaxy Note 8.0 N5100 stuck at booting animation after Step 10 then go to recovery mode (press and hold the Volume Up, Home and Power buttons together) and perform Wipe data/Factory Reset and Wipe Cache Partition task before selecting reboot system now function. In recovery mode use Volume keys to navigate between options and Power key to select the option. Please note, performing wiping task will erase your device internal memory data and not external SD card data.

Screenshot: Already updated!

Click here to know How to Root Galaxy Note 8.0 N5100 running on Android 4.1.2 XXBMD1 Jelly Bean firmware.

Thanks for Read How to Update Galaxy Note 8.0 N5100 with Android 4.1.2 XXBMD1 Jelly Bean Official Firmware Article